FIRST Robotics Competition

This product is a Pneumatic Hub Repair Service, NOT a way to purchase a Pneumatic Hub We strongly recommend reviewing the Hub Repair portion of our Warranty and Returns page before purchasing this Repair Service. If you are unsure if your...

This product is a Power Distribution Hub Repair Service, NOT a way to purchase a Power Distribution Hub. We strongly recommend reviewing the Hub Repair portion of our Warranty and Returns page before purchasing this Repair Service. If you are...

These spare parts are designed specifically to self service and maintain your 3in MAXSwerve Module (REV-21-3005). Created for efficient repairs and upkeep, routinely servicing your 3in MAXSwerve Module with spare parts will enhance performance and...

The 3in MAXSwerve Aluminum Wheel was designed for the 3in MAXSwerve Module. You can attach your favorite tread material to this wheel. REV recommends rough top conveyor belting. A cut template for the wheel tread is available below.  ...

These JST PH 6-pin Extension Cables are intended to extend the reach of sensor cables without having to cut and splice wires. Specifications Length: 30cm Notes As of 01/10/2024, the length on this product page has been corrected from 15cm to 30cm...

Power your 3in MAXSwerve Module with this proven motor and controller setup, featuring the NEO Brushless Motor and SPARK MAX Motor Controllers. Designed to work seamlessly with the 3in MAXSwerve Module, this bundle delivers reliable performance and...

Connect the REV Through Bore Encoder directly to the SPARK MAX Data Port using this adapter. This adapter connects the Absolute Duty Cycle output of the Through Bore Encoder to the correct SPARK MAX Data Port pins, leaving the incremental quadrature...

3/16in Rivets are compatible with the REV ION System are perfect for a variety of applications where a strong, permanent joint is required. Place the rivet into a hole from a single side (a “blind” hole) and then use a rivet...

Tube Nuts for 3/4in Dead Axle Tube are compatible with the REV ION System. This #10-32 tube nut presses into the end of the tube and supplies a tapped hole for easy mounting. Typically used with dead axle applications. The left-hand threaded...

The #25 Chain Turnbuckle is compatible with both the REV ION System and REV DUO System. It is designed to adjust the length of a #25 Chain by replacing a few links in a run and also allows the user to tension the chain by adjusting...

The Rounded UltraHex Shaft is compatible with the REV ION System and allows teams to adapt the REV 5mm Hex Shaft family of products to 0.5in Hex applications. It can also be used as a coupler to extend 5mm Hex shafts. Rounded UltraHex...

Designed for use with the REV ION System and with an efficient right-angle configuration, the MAX 90 Degree Gearbox offers a robust and high-performance solution to building a more compact robot. Connect the MAX 90 Degree Gearbox to the MAXPlanetary...

The 3in MAXSwerve Module Wheel Hardware Pack was designed for the 3in MAXSwerve Module. This kit is for FRC teams looking to streamline their wheel maintenance at competitions. With this kit, teams can pre-build their wheel assemblies, making...

#10-32 Ball Joint Rod Ends are compatible with the REV ION System. Right-hand threaded rod ends tighten when turned clockwise while left-handed threaded rod ends tighten when turned counterclockwise.  Specifications Type: Stud-type Rod...

The MK Battery ES17-12 is commonly used in FIRST Robotics Competition robots. Specifications Manufacturer: MK Battery Voltage: 12V Capacity: 18AH (20 Hour Rate) Product Dimensions: 7.13in x 2.99in x 6.57in Weight: 12.89lbs Documentation MK...

The Bearing Retaining Plate is compatible with the REV ION System and is designed to securely hold bearings in place, ensuring that they remain stable and aligned during use. Made from high-quality, durable materials, the Bearing...

MAXSpline Bearing Blocks are compatible with the REV ION System. Quickly add bearing support to any location on REV ION extrusion without the need for precision machining. Can also be used in a west coast style drivetrain to add center wheel drop while...

MAXTube Endcaps are designed for seamless integration with the REV ION System, providing a simple and effective solution for joining two or more MAXTube extrusions. These endcaps are pre-tapped for #10-32 hardware, ensuring quick assembly and reliable...

Steel hardware of the appropriate size to work with the REV ION System. Length measured from tip to underside of screw head. Documentation ION Build System Guide Hardware Basics Onshape Application Examples Product Options  SKU ...

Steel hardware of the appropriate size to work with the REV ION System. Length measured from tip to underside of screw head. Documentation ION Build System Guide Hardware Basics Onshape Application Examples Product Options  SKU ...

RT25 Pulleys can be combined with RT25 Belts to create a power transmission system compatible with the pitch of the ION Build System. RT25 belts and pulleys are comparable to the belts and pulleys that teams are used to using. Belts are lighter than...

RT25 Belts are toothed belts with a 1/4in pitch are compatible with the REV ION System. These belts are comparable in strength to the belts that teams are used to using while working on the pitch of the ION build system. Belts are lighter than...

ION Servo Accessories allow for easy integration into REV ION System. Mount a hobby sided servo, such as the REV Smart Robot Servo, on a 1/2in pitch. Using the adapters, you can convert a servo to a 1/2in Hex shaft for use with all other...

The MAXSpline Shaft Collar is compatible with the REV ION System and provides a simple way to retain items in place on the MAXSpline Shaft. The shaft collar can also be bolted to structure to constrain the axial alignment of MAXSpline Shaft when used in...

The Stepped Bushing - 3/4in ID is compatible with the REV ION System. This bushing used in conjunction with the MAXSpline Shaft and Dead Axle Tube - 3/4in can be used to build robust and effective rollers and intakes. Specifications ...

The 3/4in External Retaining Ring is compatible with the REV ION System and is used to constrain movement on the Dead Axle Tube - 3/4in for intake and roller applications. Specifications Material: Steel Documentation ION Build System...

The 8mm Shaft Spacer is compatible with the REV ION System and is a convenient way to space pinions and gears along the shaft of the NEO Brushless Motor. The 8mm Shaft Spacer is bigger than the 1/2in Hex Adapter and can help keep...

The WAGO 221 Inline Splicing Connector is a robust and easy to use splicing connector that makes fiddling with hard-to-master crimp-style connectors a thing of the past. Simply lift the lever up, insert the stripped wire, and push the lever back down to...

The Elevator Bearing Blocks family offers reliable, versatile solutions for creating linear motion in elevator systems using MAXTube. Both the original Elevator Bearing Block and the Clamping Elevator Bearing Block provide teams with the flexibility to...

Mounting your SPARK MAX Motor Controller (REV-11-2158) has never been easier with the help of the SPARK MAX Mounting Bracket. Configured with a hole pattern compatible with a 1/2in grid and allowing the mode and status light to be seen, this...

The MAXPlanetary 550 Input Kit gives users the ability to use 550 size motors with the MAXPlanetary System.  Features Does not require permanent modifications to the motor Press-fit shaft adapter avoids set screws that can come loose...

The MAXPlanetary 775 Input Kit gives users the ability to use 775 size motors (775pro or AM RedLine) with the MAXPlanetary System. Features Does not require permanent modifications to the motor Press-fit shaft adapter avoids set screws that...

REV Robotics custom ATO sized auto-resetting breakers are designed to give reliable protection for FRC robot actuators.  These custom developed breakers adhere to SAE Standard J553 and will give consistent performance even after hundreds of breaker...

REV Robotics custom ATO sized auto-resetting breakers are designed to give reliable protection for FRC robot actuators. These custom developed breakers adhere to SAE Standard J553 and will give consistent performance even after hundreds of breaker trips...

REV Robotics custom ATO sized auto-resetting breakers are designed to give reliable protection for FRC robot actuators. These custom developed breakers adhere to SAE Standard J553 and will give consistent performance even after hundreds of breaker trips...

REV Robotics custom ATO sized auto-resetting breakers are designed to give reliable protection for FRC robot actuators.  These custom developed breakers adhere to SAE Standard J553 and will give consistent performance even after hundreds of breaker...

This update to the SPARK MAX CAN Cable bridges the H and L CAN signals together within the cable itself. This prevents the CAN Bus breaking in the event of a cable disconnecting from a SPARK MAX Motor Controller. These SPARK MAX CAN cables have a JST-PH...

The NEO Pinions are used for transferring power from a NEO Brushless Motor to a mechanism. These pinions come in three different types; either gear, sprocket, or pulley. The pinion gears are compatible with 20DP gears. The pinion sprocket is...

The 550 Motor Pinions are used for transferring power from a 550 class motor, like the HD Hex Motor or NEO 550, to a mechanism. These pinions come in four different types. The 32DP pinion gear is compatible with 32DP gears,the UltraPlanetary Pinion is...

The Digital LED Indicator is a LED signal module that is digitally controlled (active low) and offers three colors: red, green, and amber. The Digital LED Indicator is designed to directly interface with the DIO ports of the Expansion Hub or Control Hub...

With the 8mm to 1/2in Hex Adapter you can convert 8mm keyed shafts to drive 0.5in hex bore wheels, sprockets, gears, and more! Use these with any motors with a 8mm round keyed output shaft, like the NEO Brushless...

The 36in CAN Extension Cable is a 3-pin connector to interface with existing CAN devices.  Specifications Length: 36in (3ft) Wire Colors: yellow, green 22 AWG

The Aluminum Servo Horn V2 is compatible with the REV Smart Robot Servo and any other servos with a standard 25T spline. Updates from the original Aluminum Servo Horn include additional tapped M3 Holes for more mounting options, 6 M3 Clearance Holes...

Connect the REV Through Bore Encoder directly to the SPARK MAX Data Port when it is configured in Alternate Encoder Mode using this adapter. This adapter is not intended for use with the default Data Port configuration or with other...

This is a longer version of the USB-A to USB-C cable included with the SPARK MAX Motor Controller and the Control Hub. Use this cable to connect your SPARK MAX or Control Hub to a standard computer from up to 2 meters away. Features Longer than the...

This 4-pin JST PH to 4-pin roboRIO I2C Cable is designed to connect REV I2C sensors, like the REV Color Sensor V3, to the I2C port on the NI roboRIO for use in the FIRST Robotics Competition. Each cable is approximately 36 inches long. This cable...

The JST PH 6-pin to 4 Channel PWM Cable allows for seamless connection of the Through Bore Encoder into the FRC control system (roboRIO).

This is all of the hardware included in the UltraPlanetary Gearbox Kit & HD Hex Motor (REV-41-1600) Kit Contents QTY 6 - M3x40mm QTY 6 - M3x30mm QTY 6 - M3x20mm QTY 6 - M3x10mm QTY 2 - M3x8mm Button head QTY 2 - M3x6mm Set Screw  Documentation...

An individual cartridge for the UltraPlanetary System. This cartridge is nominally a 5:1 gear reduction. The UltraPlanetary System is a cartridge based modular gearbox designed to handle the rigors of the competition and the classroom. Building on the...

An individual cartridge for the UltraPlanetary System. This cartridge is nominally a 4:1 gear reduction. The UltraPlanetary System is a cartridge based modular gearbox designed to handle the rigors of the competition and the classroom. Building on the...

An individual cartridge for the UltraPlanetary System. This cartridge is nominally a 3:1 gear reduction. The UltraPlanetary System is a cartridge based modular gearbox designed to handle the rigors of the competition and the classroom. Building on the...

1in Extrusion is compatible with the REV ION System. It’s a 1in x 1in square extruded aluminum tube, with slots designed to fit standard #10 hardware rather than expensive t-nuts. Take your robot mechanisms to a new level of sleekness with the...

The SPARK MAX Data Port Breakout Board makes it easy to connect external sensors to the SPARK MAX Data Port. For additional information on the SPARK MAX Data Port, please take a look at the SPARK MAX User's Manual. Analog Input Issue - Affects Rev. A...

This JST-PH 6-pin Breakout Board is designed to adapt external sensors to the SPARK MAX 6-pin Encoder Port standard. It features a JST PH 6-pin connector, labeled solder pads, and through-hole pads that are compatible with popular 63R style quadrature...

These JST PH 6-pin Joiner Boards are intended to be used with the JST PH 6-pin Extension Cables to extend the reach of your NEO Brushless Motor sensor cables.

These JST PH 6-pin Extension Cables are intended to extend the reach of sensor cables without having to cut and splice wires. Specifications Length: 36in

These SPARK MAX PWM Cables have a JST-PH 4-pin connector on one end, and a 0.1in 3-pin female PWM connector on the other. They are designed to convert the SPARK MAX Motor Controller's PWM/CAN port to a standard 3-pin PWM port on a robot controller. The...

These plastic clips are designed to keep standard 0.1" 3-pin PWM connectors together. Simply clip them around an assembled pair of connectors.

These plastic inserts are designed to go into the SPARK MAX Data Port to protect it from debris.

A custom-designed tool that allows teams to easily break and re-assemble #25 chain. The mandrel is used to push out the chain pin. If using master links, the pin can be completely removed, but the depth guide screw allows the option of partially pressing...

The REV Robotics 2m Distance Sensor uses the ST Microelectronics VL53L0X Time-of-Flight (ToF) laser-ranging module to measure distances up to 2 meters with millimeter resolution. Unlike other ranging sensors that rely on the intensity of reflected light,...

The REV POE Injector Cable was specifically designed to address a common problem for many FRC teams with their wireless radios: intermittent power glitches. The wireless radios used in the last several FRC seasons can be powered either through a...

Blinkin makes adding LEDs to your robot as simple as driving a motor. Chose the pattern you want and give it the corresponding PWM signal. The REV Blinkin LED Driver is a compact LED driver module that simplifies controlling both 12V RGB LED and 5V...

Touch sensor is best used for user input, but can also be used as a limit switch.  Configuration The REV Touch Sensor is a digital sensor that is wired to the N+1 channel on our standard 4-pin JST PH connector. In other words, the REV Expansion Hub...

Nylon Zip Ties with rounded edges to prevent snagging. Length is idea for cable management and many other uses. Specifications 160mm long Quality nylon construction 18lb. tensile strength

Double-sided hook and loop tape allows you to cut to desired custom lengths. Reusable, secure hold. Specifications 13.5mm width x 2m length

This stretchy latex rubber tubing is sized to fit through any of the M3 holes in DUO brackets, wheels, gears or other motion products. String tubing between outside holes on two wheels to create a compliant intake.  Specifications Color: Black...

 PWM Y-cable, is used for splitting the signal from the roboRIO so you can drive multiple motor controllers or servos from a single source. Specifications Length: 12in Wire colors: white, red, black Wire jacketing: black heat shrink tubing 22 AWG

2-pin header cable that can be used for connecting signals, sensors or any other spots on robots. Features 2 female 0.1in pitch connectors on each end.  Specifications Pins: 2 pin Wires: 2 wire Length: 36in  

PWM Cables, which are used for connecting things like the SPARK Motor controller to the roboRIO. These can also be used as servo extension cables for getting signal and power a bit farther away than integrated wires can reach. Specifications Length:...

The Servo Power Module is a 6V 90W power injector that enables the use of high-power RC servos in applications where a robot controller cannot directly provide adequate power.  The Servo Power Unit passes through input signals unaltered while...

Single Strand #25 roller chain for use with #25 sprockets. Use a master link (connecting link) for #25 chain connect two ends of chain to create a loop. Specifications Material: Steel Size: #25 Pitch: 0.25in

Master link (connecting link) for #25 chain. Use a master link to connect two ends of chain to create a loop. Specifications Material: Steel Size: #25 Pitch: 0.25in CAD & Drawings REV-41-1366 STEP File REV-41-1366 Onshape

Zinc plated steel nuts compatible with all REV M3 screws or bolts. Contains a nylon insert which increases grip on screw, reducing the chance of the nut loosening over time. Does NOT fit in the channel of our REV DUO 15mm Extrusion System. Specifications...

The REV Smart Robot Servo (SRS) is a configurable metal-geared servo that takes the guesswork out of aligning and adjusting servo based mechanisms. One SRS can be used as a standard angular servo, a custom angular servo, and a continuous rotation servo...

The NEO 550 Brushless Motor is a member in the NEO family of brushless motors. Its output power and small size are specifically designed to make NEO 550 the perfect motor for intakes and other non-drivetrain robot mechanisms. Mounting holes and pilot...

The Through Bore Encoder is specifically designed with the end user in mind, allowing teams to place sensors in the locations closest to the rotation that they wish to measure. This rotary sensor measures both relative and absolute position through its...

The UltraPlanetary Female 5mm Output V2 is the output stage of the UltraPlanetary System. With two different ways to transfer power, the output stage allows designers to choose the option best suited for the application. The V2 version of the...

Split Lock washer with a 3/8in inner diameter. Specifications Material: Zinc-plated Steel ID: 3/8in OD: 0.680in Thickness: 0.094in Documentation ION Build System Guide #10 Hardware Basics CAD & Drawings REV-29-1240 Drawing

Steel hardware of the appropriate size to work with the ION Build System 1in Extrusion. Length measured from tip to underside of screw head. Specifications Material: 18-8 Stainless Steel Diameter & Thread: #10-32 Length: 1-1/2in Documentation ION...

The REV 4-Pin JST to PWM Sensor Adapter Cable allows for seamless connection of REV Robotics Sensors like the Magnetic Limit Switch and Potentiometer to the FRC Control System. Please note that this cable will not work for I2C type sensors. REV...

This 5V WS2812B Addressable RGB LED Strip is compatible with the REV Blinkin LED Driver (REV-11-1105). Each LED contains an integrated driver IC and three LEDs; a red, green, and blue LED. Each individual LED can be controlled to create colorful patterns...

This 12V RGB LED Strip is compatible with the REV Blinkin LED Driver (REV-11-1105). Each LED on the strip is wired in parallel and actually contains three embedded LEDs; a red, green, and blue LED. Each color can be controlled separately to create any...

The Magnetic Limit Switch is a three-sided active-low digital hall effect switch with three internal hall effect elements located on the top and sides of the sensor. The three elements are connected in parallel so that any one of them will trigger the...

The REV Robotics SRS Programmer is the key to unlocking all the smart features of the (SRS) Smart Robot Servo (sold separately). Switching between continuous rotation, standard servo, and custom angular modes is easy as pressing a button...

This Eye-to-Eye Turnbuckle is ideal for tensioning string, cordage, or cabling in linear motion applications. The welded eyes provide significantly more strength than bent eyes. Specifications Material: Steel Thread: M5 Retracted Length: 106mm +- 1mm...

The 1in Extrusion Endcap Slide allows teams to create compact and robust multistage lifts when combined with the 1in Linear Motion Kit (REV-15-1189) and the 1in Extrusion (REV-21-1000). The slide tab is offset allowing stages to fully nest when collapsed...

High-strength and low-stretch cord that is ideal for actuating lifts and other linear mechanisms. Also known as Spectra or Dyneema, this cord type minimizes the need for adjustments and re-tensioning after first assembly due to its low-stretch properties...

For use with the ION Build System 1in Extrusion to create linear motion.   Kit Contents QTY 1 - REV-21-1032 - Dual Bearing Plate QTY 1 - REV-21-1029 - Eccentric Bushing QTY 1 - REV-21-1030 - Concentric Bushing QTY 2 -...

The UltraPlanetary 1/2in Hex Adapter is designed to face mount to the UltraPlanetary gearbox and provide a convenient 1/2in hex output shaft that is commonly used in the FIRST Robotics Competition. The recommended hardware for mounting the...

These are the same inserts that are included with the Through Bore Encoder.  Specifications Weight(s):  3/8in Hex: 23.5g (0.051lbs) 5mm Hex: 24.0g (0.052lbs) 1/4in Round: 24.0g (0.052lbs) Kit Contents QTY 1 - 3/8in Hex to 1/2in Hex...

Aluminum Servo Arm that is compatible with the REV Smart Robot Servo. Lightweight and strong, this arm is best utilized under high and low torque applications. Specifications Material: 6061 Aluminum CAD & Drawings SKU-STP REV-41-1820 Onshape...

Eccentric bushings are used to hold our V-Groove Bearings (REV-29-1014) for linear motion applications. The hole is drilled off-center of the bearing axis so by rotating the bushing on its mounting bolt, the clearance between the wheel and track can...

This dual bearing plate holds two V-Groove Bearings (REV-29-1014) to create an easy linear motion system for the ION Build System 1in Extrusion (REV-21-1000). Using a combination of Concentric (REV-21-1030) and Eccentric (REV-21-1029) bushings, the user...

Concentric bushings are used to hold our V-Groove Bearings (REV-29-1014) for linear motion applications. Used in conjunction with our Eccentric Bushing (REV-21-1029), the user can adjust how tight or loose they would like to tune their linear...

The REV Robotics Analog Pressure Sensor is a 5V sensor that can measure pressures up to 200 PSI. It outputs an analog voltage that is proportional to the measured pressure and can plug directly into the roboRIO or the More Board V2.0. Applications ...