FTC Discounts

With an efficient right-angle configuration, the Ultra 90 Degree Gearbox offers a robust solution to building a more compact robot. The Ultra 90 Degree Gearbox allows you to connect the UltraPlanetary Gearbox and the HD Hex Motor (REV-41-1600)...

The REV USB PS4 Compatible Gamepad is compatible with both the REV DUO and REV ION Systems. Plug the REV Gamepad directly into a Driver Hub to enable feature rich control of your robot. Additionally, when plugged into a PC, it offers an Xbox...

GT2 3mm Pitch Belts are compatible with both the REV ION System and the REV DUO System. These belts go hand in hand with GT2 timing pulleys. Use belts and pulleys in tight to fit areas where adjustment is difficult. Specifications Pitch: 3mm Width:...

DUO Flap Wheels are compatible with the REV DUO System and feature a 5mm Hex Bore. They are used on intakes to pick up irregular gamepieces, playing a similar role to compliant wheels. While compliant wheels provide compliance with minimal slip between...

The #25 Chain Turnbuckle is compatible with both the REV ION System and REV DUO System. It is designed to adjust the length of a #25 Chain by replacing a few links in a run and also allows the user to tension the chain by adjusting...

The Rounded UltraHex Shaft is compatible with the REV ION System and allows teams to adapt the REV 5mm Hex Shaft family of products to 0.5in Hex applications. It can also be used as a coupler to extend 5mm Hex shafts. Rounded UltraHex...

M3 Spacers are compatible with the REV DUO System and accurate way to space gears, sprockets, wheels, and other parts on a M3 bolt.  

Washer for use with REV DUO M3 hardware.

5mm Hex Shafts are compatible with the REV DUO System. The hex shaft interface completely eliminates the need for expensive hubs or using potentially unreliable set screws. REV shafts are made out of strong, corrosion resistant stainless steel...

DUO Omni Wheels are compatible with the REV DUO System and have rollers mounted around the outside which passively rotate at 90 degrees to the powered direction of the wheel. DUO Omni Wheels can be used to make it easier to turn with skid steer...

DUO Traction Wheels are compatible with the REV DUO System and fit on a 5mm hex shaft. The hex shaft interface completely eliminates the need for expensive hubs or using potentially unreliable set screws. DUO Traction Wheels 60mm in...

DUO Round Belt Pulleys are compatible with the REV DUO System and are perfect for your conveyor and intake mechanisms when combined with Polyurethane Hollow Round Belting. Documentation DUO Build System Guide Product...

Through Bore Bearings are compatible with the REV DUO System and are used with 5mm Hex Shafts recommend for the DUO Extrusion System to provide a low friction rotating shaft support. These low profile bearings fit in any of the 3mm...

5mm Metal Hex Bore Gears are compatible with the REV DUO System and work with REV 5mm hex shafts in high-load applications. REV metal gears are NOT compatible with REV plastic gears. All REV metal gears are narrower than plastic...

5mm Plastic Hex Bore Gears are compatible with the REV DUO System and fit on a 5mm hex shaft. The hex shaft interface completely eliminates the need for expensive hubs or using potentially unreliable set screws. Gears 45 tooth...

UltraPlanetary Brackets are compatible with the REV DUO System. Each bracket includes holes on an 8mm grid that is compatible with many other building systems. The UltraPlanetary Outside Mounting Bracket (REV-41-1621) is used to...

DUO Plastic #25 Sprockets are compatible with the REV DUO System and fit on a 5mm hex shaft. The hex shaft interface completely eliminates the need for expensive hubs or using potentially unreliable set screws. Sprockets 15 tooth and...

15mm Metal Brackets are compatible with the REV DUO System. Each bracket includes holes on an 8mm grid that is compatible with many other building systems.  The 15mm Metal Bent Core Hex Motor Bracket V2 (REV-41-1433) is used to mount the...

15mm Metal Brackets are compatible with the REV DUO System. Each bracket includes holes on an 8mm grid that is compatible with many other building systems.  Specifications Material: 6061 Aluminum Thickness: 2mm Mounting Holes: 3.4mm...

15mm Plastic Motion Brackets are compatible with the REV DUO System. Each bracket features a set of alignment ribs designed to seat the bracket into the extrusion channel increasing joint alignment, strength, and rigidity.  The 15mm Plastic...

15mm Plastic Brackets are compatible with the REV DUO System. Each bracket includes a set of alignment ribs designed to seat the bracket into the extrusion channel increasing joint alignment, strength, and rigidity. The 15mm Plastic Variable Angle...

DUO Compliant Wheels are used for intakes and conveyor systems. Featuring a solid 5mm Hex Hub molded into the wheel making sure more power is driven by the wheel, combined with the “hurricane” cutouts to ensure even compliance across the...

DUO Grip Wheels are used for intakes, conveyor systems, and shooters. With a solid 5mm Hex Hub molded into the wheel no external hub is required. These wheels come in two different durometers, Soft - Light Gray 30A and Medium - Gray 40A. As the tread...

Replacement battery for the Driver Hub (REV-31-1596). Specifications 5040 mAH Li-ion battery  Documentation Driver Hub User's Manual Driver Hub Getting Started Guide Driver Hub Battery Best Practices

The 550 Motor Pinions are used for transferring power from a 550 class motor, like the HD Hex Motor or NEO 550, to a mechanism. These pinions come in four different types. The 32DP pinion gear is compatible with 32DP gears,the UltraPlanetary Pinion is...

The Digital LED Indicator is a LED signal module that is digitally controlled (active low) and offers three colors: red, green, and amber. The Digital LED Indicator is designed to directly interface with the DIO ports of the Expansion Hub or Control Hub...

The USB Female A to Micro USB Adapter allows you to use standard USB devices with micro 5-pin oriented electronics. Use this cable adapter to connect a Robot Controller phone to an Expansion Hub, or to connect a Driver's Station phone to a single...

The Aluminum Servo Horn V2 is compatible with the REV Smart Robot Servo and any other servos with a standard 25T spline. Updates from the original Aluminum Servo Horn include additional tapped M3 Holes for more mounting options, 6 M3 Clearance Holes...

The 15mm Extrusion Lift Kit offers an assortment of components needed to build an un-powered 3-stage continuous or cascading lift. The basics of the linear motion kit can be found on the Introduction to Linear...

Tote around your extra robot parts with the classic REV Storage Tote. This is the same tote included with the FTC Starter Kit V3 and FTC Starter Kit V2. Specifications Color: Orange Width: 22in Height: 13.79in Depth: 9in

Custom zinc plated steel drop-in hardware to work with the 15mm Extrusion system. Length measured from tip to underside of hex cap. Specifications Thread Pitch: M3 x 0.5 Material: Corrosion resistant zinc plated steel Length:...

This Motion Pattern Spacer offers a convenient and accurate way to space gears, sprockets, wheels, and other parts through the Motion Pattern interface. Great for getting the proper spacing when face mounting to the UltraPlanetary Gearbox...

This is a longer version of the USB-A to USB-C cable included with the SPARK MAX Motor Controller and the Control Hub. Use this cable to connect your SPARK MAX or Control Hub to a standard computer from up to 2 meters away. Features Longer than the...

The JST PH 6-pin to JST PH 4-pin Cable allows for seamless connection of the Through Bore Encoder to the dedicated encoder ports on the FTC Control System (Expansion Hub or Control Hub). Also allows for the HD Hex Motor to...

This sensor can be used to read and compare colors, and also has a built-in IR (optical) Proximity Sensor and white LED for active target lighting. Supports High Speed I2C Communication (400kHz) as well as auto increment register read which allows the...

REV Building System also comes in a 15mm x 30mm square extrusion. The slots are designed to fit standard M3 hardware rather than expensive t-nuts. Use the 15mm x 30mm extrusion when more strength is needed for an application. Features All holes can be...

This is all of the hardware included in the UltraPlanetary Gearbox Kit & HD Hex Motor (REV-41-1600) Kit Contents QTY 6 - M3x40mm QTY 6 - M3x30mm QTY 6 - M3x20mm QTY 6 - M3x10mm QTY 2 - M3x8mm Button head QTY 2 - M3x6mm Set...

An individual cartridge for the UltraPlanetary System. This cartridge is nominally a 5:1 gear reduction. The UltraPlanetary System is a cartridge based modular gearbox designed to handle the rigors of the competition and the classroom. Building on the...

An individual cartridge for the UltraPlanetary System. This cartridge is nominally a 4:1 gear reduction. The UltraPlanetary System is a cartridge based modular gearbox designed to handle the rigors of the competition and the classroom. Building on the...

An individual cartridge for the UltraPlanetary System. This cartridge is nominally a 3:1 gear reduction. The UltraPlanetary System is a cartridge based modular gearbox designed to handle the rigors of the competition and the classroom. Building on the...

Tested for the rigors of competition, REV Mecanum Wheels are steel plates with rollers supported by ball bearings allowing for the perfect combination of wheel rigidity and roller movement. Included in the set of wheels are Universal Hex Adapter making...

These Ferrite Cable Clips help prevent electromagnetic interference (EMI). They can be clipped around USB and other data cables that are being used in electrically noisy environments.

The 3-pin JST PH Cable is keyed and locking for improved reliability. Use this cable along with an XT30 Extension cable to connect a second REV Robotics Expansion Hub. Expansion Hub 3-pin JST PH Connections: RS485 - Daisy-chain communication to a second...

Safely ground your robot's metal frame with this Resistive Grounding Strap. This strap has a built in 470Ω resistor to prevent high-current discharges while still minimizing the difference in charge between the robot electronics and the frame...

Metal gears designed to work with REV 5mm hex shafts in high-load applications. REV metal gears are NOT compatible with REV plastic gears. All REV metal gears are narrower than plastic gears, allowing for compact drivetrains and gearboxes within the same...

Metal gears designed to work with REV 5mm hex shafts in high-load applications. REV metal gears are NOT compatible with REV plastic gears. All REV metal gears are narrower than plastic gears, allowing for compact drivetrains and gearboxes within the...

Metal gears designed to work with REV 5mm hex shafts in high-load applications. REV metal gears are NOT compatible with REV plastic gears. All REV metal gears are narrower than plastic gears, allowing for compact drivetrains and gearboxes within the...

Metal gears designed to work with REV 5mm hex shafts in high-load applications. REV metal gears are NOT compatible with REV plastic gears. All REV metal gears are narrower than plastic gears, allowing for compact drivetrains and gearboxes within the...

Custom hinge system used to create compact, simple hinges using REV DUO 15mm Extrusion. Hinges come in left, right, and center pieces, and are attached together using standard M3 hardware. Specifications Hole Diameter: M3 clearance Hole Spacing:...

Updated version of our popular Linear Motion Kit. This kit has been redesigned to be even easier for teams to use with REV 15mm Extrusion to create compact linear slides. New additions to the kit include End Cap pieces to keep lift stages in place,...

A custom-designed tool that allows teams to easily break and re-assemble #25 chain. The mandrel is used to push out the chain pin. If using master links, the pin can be completely removed, but the depth guide screw allows the option of partially pressing...

Aluminum cubes that allow users to quickly create square assemblies using REV 15mm Extrusion. The cubes are machined from aluminum and feature holes sized to accept standard M3 hardware. 2 pieces of extrusion can be used to create flat assemblies, 3...

Reduce the number of USB disconnects between the Expansion Hub and your Robot Controller Phone with our USB Retention Mount. When used with the included right-angle USB cable, this mount provides a strong, reliable connection between the cable and the...

Easily connect multiple devices to your robot battery with the REV XT30 Power Distribution Block. Allows for clean, compact wiring of all your XT30-connected devices. Compatible with: Expansion Hub, Blinkin LED Driver, SPARKmini, Servo Power Module, and...

The REV Robotics 2m Distance Sensor uses the ST Microelectronics VL53L0X Time-of-Flight (ToF) laser-ranging module to measure distances up to 2 meters with millimeter resolution. Unlike other ranging sensors that rely on the intensity of reflected light,...

The REV Punch Tube is designed to enable teams to rapidly prototype ideas and build robots without some of the constraints generally associated with extrusion based construction. When paired with our Metric Step Drill (REV-49-1455) and 1/8in or 3.2mm...

Blinkin makes adding LEDs to your robot as simple as driving a motor. Chose the pattern you want and give it the corresponding PWM signal. The REV Blinkin LED Driver is a compact LED driver module that simplifies controlling both 12V RGB LED and 5V...

This gearbox is the same one used on our HD Hex Motor 20:1 Spur Gearbox featuring our 5mm HEX output shaft! This gearbox can be installed on any 550 series motors (like the NeveRest motors from AndyMark) giving you the convenience and...

For smaller applications the DUO Build System also comes in a 15mm x 15mm square extrusion. The 15mm profile of the 15mm Extrusion has slots on on all four sides that accept standard M3 hardware. Rather than using a T-nut, which is more expensive, slide...

For smaller applications the DUO Build System also comes in a 15mm x 15mm square extrusion. The 15mm profile of the 15mm Extrusion has slots on on all four sides that accept standard M3 hardware. Rather than using a T-nut, which is more expensive, slide...

For smaller applications the DUO Build System also comes in a 15mm x 15mm square extrusion. The 15mm profile of the 15mm Extrusion has slots on on all four sides that accept standard M3 hardware. Rather than using a T-nut, which is more expensive, slide...

All the drills you need for FTC in one handy tool! Specifications Maximum material thickness: 3mm Tool material: High-Speed Steel Shank: 0.25in Hex 10 unique diameters 3, 4, 5, 6, 7, 8, 9, 10, 11, & 12 mm Hole Size Compatibility 3mm Clearance...

These small connector boards can be used to join two JST VH 2-pin Motor Cables to create a longer cable. 

Zinc plated steel nuts compatible with all REV DUO M3 screws or bolts. This is a plain nut which does NOT contains a nylon insert.  Specifications Thread Pitch: M3 x 0.5 Material: Corrosion resistant zinc plated steel Width: 5.5mm Height: 2...

The XT30 Extension Cable is keyed and locking for improved reliability. Use this cable along with an 3-pin JST PH Cable to connect a second REV Robotics Expansion Hub. Expansion Hub XT30 Connections: Power, One Male and One Female XT30 Connector ...

These small connectors can be used to join two JST PH 4-pin Sensor Cables to create a longer cable. 

The 2-pin JST VH Cable is keyed and locking for improved reliability.  Expansion Hub 2-pin JST VH Connections: Motor Power Product Options  SKU   PRODUCT NAME   REV-31-1412-PK4   JST VH 2-pin Motor Cable -...

The 4-pin JST PH Cable is keyed and locking for improved reliability.  Expansion Hub 4-pin JST PH Connections: Motor Encoder Digital Analog I2C Product Options  SKU   PRODUCT NAME   REV-31-1407-PK4   JST PH...

Charger for use with our 12V Slim Battery. The output is wired with an XT30 male connector for charging. For the input, the battery charger has an IEC C13 power cord to standard, grounded, North America wall outlet plug (NEMA 5-15). *Do not...

Add this switch between your battery and Expansion Hub to have convenient on/off control of your robot. We recommend mounting the switch slightly recessed from the outside of your robot so that it's not accidentally turned off by another robot during a...

Use the Anderson Power Pole to 2-pin JST VH Adapter Cable to connect your existing motors to the REV Robotics Expansion Hub. Teams that already own and use the Anderson Powerpole Crimper may purchase JST VH 2-pin Motor Cables (REV-31-1413), cut cables in...

The analog and digital ports on the Control Hub and Expansion Hub combine two sensor inputs into one connector to save space. Single sensors plugged directly into these ports will work, but they will block access to the second input. The Sensor Splitter...

Use these connectors to create your own custom length power wires. The XT30 Connector uses a solder cup instead of a crimping tool to connect the contact to a wire. 

Cross over cable to convert the pin out from Modern Robotic's I2C sensors to work with the REV Robotics's Logic Level Converter. 

High strength string for use with the small Pulley Bearings and the 15mm Linear Motion Kit to create a powered lift.   Specifications Material: Ultra-high-molecular-weight Polyethylene (UHMWPE) Load Rating: 300lb+ Diameter: 1.2mm...

8cm long Anderson Power Pole style connector to Female XT30 adapter cable used to covert team-modified battery connectors to the new XT30 connector.  Teams that already own and use the Anderson Powerpole Crimper may purchase XT30 Extension Cables...

8cm long Female Tamiya to Female XT30 adapter cable used to covert legacy battery connectors to the new XT30 standard. 

Touch sensor is best used for user input, but can also be used as a limit switch.  Configuration The REV Touch Sensor is a digital sensor that is wired to the N+1 channel on our standard 4-pin JST PH connector. In other words, the REV Expansion Hub...

The REV Robotics Logic Level Converter is a circuit board which generates a 5V output from the 3.3V input and uses a MOSFET on each signal line to create a bidirectional communication appropriate for a variety of digital signals include I2C communication...

This battery plate is the perfect size to support a REV 12v Battery, REV Control Hub, or REV Expansion Hub. CAD & Drawings REV-41-1166 STEP File REV-41-1166 Onshape REV-41-1166 Drawing  

Nylon Zip Ties with rounded edges to prevent snagging. Length is idea for cable management and many other uses. Specifications 160mm long Quality nylon construction 18lb. tensile strength

Double-sided hook and loop tape allows you to cut to desired custom lengths. Reusable, secure hold. Specifications 13.5mm width x 2m length

12-point combination wrench for use with M3 hardware. Specifications Chrome vanadium steel 5.5mm  15° angled ring head

Use these barbs with our Polyurethane Hollow Belt to join the ends and make custom length belts quickly and easily.  CAD & Drawings REV-41-1165 Drawing

Our Polyurethane Hollow Round Belting is perfect for your conveyor, and intake mechanisms. Use Barbs to assemble custom length belts. 

This stretchy latex rubber tubing is sized to fit through any of the M3 holes in DUO brackets, wheels, gears or other motion products. String tubing between outside holes on two wheels to create a compliant intake.  Specifications Color:...

This 10K potentiometer can be used as an analog sensor with the Control Hub or Expansion Hub. This potentiometer has a 270 degree range of motion and can be mounted to any REV DUO brackets with the Motion Pattern, like the Motion Bracket. The...

PWM Cables, which are used for connecting things like the SPARK Motor controller to the roboRIO. These can also be used as servo extension cables for getting signal and power a bit farther away than integrated wires can reach. Specifications Length:...

The Servo Power Module is a 6V 90W power injector that enables the use of high-power RC servos in applications where a robot controller cannot directly provide adequate power.  The Servo Power Unit passes through input signals unaltered while...

This gearbox is the same one used on our HD Hex Motor 40:1 Spur Gearbox featuring our 5mm HEX output shaft! This gearbox can be installed on any 550 series motors (like the NeveRest motors from AndyMark) giving you the convenience and...

These v-groove bearing pulleys fit on an M3 x 16mm Hex Cap Screw and can be mounted directly onto extrusion. Use with 15mm Linear Motion Kits and a high tensile strength no-stretch string, such as kevlar string or spectra fishing line, to create an...

Single Strand #25 roller chain for use with #25 sprockets. Use a master link (connecting link) for #25 chain connect two ends of chain to create a loop. Specifications Material: Steel Size: #25 Pitch: 0.25in

Master link (connecting link) for #25 chain. Use a master link to connect two ends of chain to create a loop. Specifications Material: Steel Size: #25 Pitch: 0.25in CAD & Drawings REV-41-1366 STEP File REV-41-1366 Onshape

Zinc plated steel nuts compatible with all REV M3 screws or bolts. Contains a nylon insert which increases grip on screw, reducing the chance of the nut loosening over time. Does NOT fit in the channel of our REV DUO 15mm Extrusion System...

Small electronics sized 5.5mm Nut Driver with rubberised grip fits M3 hex cap bolts and nuts. Specifications Socket Depth: 15.8mm Dimensions: 16.2cm x 2cm x 2cm (6.38in x 0.79in x 0.79in) Weight: 33g (1.16oz)

This 10-cell, 12V 3000mAh battery has a low profile configuration to make it easier to mount on a robot. The Slim Battery pack is wired with an XT30 male connector and an inline 20A replaceable ATM fuse. XT30 to Tamiya Adapter no longer automatically...