Motion

Introducing the 25 Pack Classroom Set of the FRC Robot Basics Guidebook The FRC Robot Basics Guidebook is your go-to resource for understanding the fundamental components and techniques used in the FIRST Robotics Competition. Whether you’re a...

The NEO Vortex is a high-power, high-performance, and high-resolution sensored brushless motor that is compatible with the REV ION System. It features a dockable controller interface that can be mounted directly to the SPARK Flex Motor Controller or our...

The Vortex Shaft - MAXSwerve Integrated Key is compatible with the REV ION System and gives users the ability to drive a MAXSwerve Module without the need for the MAXSwerve Key. This eliminates a potential point of failure in the MAXSwerve since the key...

The Vortex Shaft - 20DP Gear - 7T is compatible with the REV ION System and offers users the unique ability to achieve substantial gear reductions directly from the motor. This gear features a 7T 20DP design that is typically too small for an 8mm keyed...

The Vortex Shaft - Falcon Compatible Spline is compatible with the REV ION System and gives users the ability to drive components that have a falcon spline bore. *Falcon is not a REV trademark. Featuring a 1/2in hex section that drives the shaft and a...

The 8mm Vortex Shaft, compatible with the REV ION System, empowers you to utilize the NEO Vortex Brushless Motor with any 8mm keyed shaft component. This interchangeability also means that the NEO Vortex matches the output of a NEO Brushless Motor V1.1,...

The Vortex MAXPlanetary Input Kit is compatible with the REV ION System and gives users the ability to mount a MAXPlanetary Gearbox directly to your NEO Vortex Brushless Motor and SPARK Flex Motor Controller. Working seamlessly with the MAXPlanetary...

The NEO Vortex Solo Adapter, allows teams to seamlessly integrate the NEO Vortex Brushless Motor with a SPARK MAX Motor Controller. This adapter breaks out the motor sensor connector and phase wire connections. While the NEO Vortex Solo Adapter allows...

The 3in MAXSwerve Module is the smallest and lightest swerve module designed for FRC Teams. Leveraging many parts of the REV ION System, MAXSwerve aims to reduce the complexity traditionally associated with swerve drivetrains. The module features a 3in...

The Gear Ratio Upgrade Kit is compatible with the REV ION System and works with the 3in MAXSwerve Module and comes with two additional motor pinions and four additional spur gears that create five new extra high speed ratios to make your drive faster and...

The MAX 180 Degree Gearbox is compatible with the REV ION System and is designed to give you extra flexibility in your robot construction. Engineered to let you flip your motor 180 degrees to the output, optimizing space for tighter packaging. This...

The Linear Actuator - 12in Stroke is compatible with the REV ION System. This electric linear actuator aligns seamlessly with FRC-legal motors and gearboxes while adhering to FRC hardware and mounting standards. Designed for adaptability, this...

The 2 Motor Gearbox - Through Bore is compatible with the REV ION System. This two motor into one output gearbox allows the user to adjust the gear ratio by changing pinion and cluster gear (12:60, 18:54, 24:48, or 36:36). The output shaft is 1/2in...

The 2 Motor Drivetrain Gearbox - Through Bore is compatible with the REV ION System and can be mounted in a variety of options, including flush with tube or spaced away from the tube to enable both chain in tube and chain/belt outside tube designs...

The NEO Brushless Motor is the first brushless motor designed to meet the unique demands of the FRC community. NEO offers an incredible power density due to its compact size and reduced weight. As it is designed to have similar performance...

The MAXPlanetary System is a cartridge-based modular planetary gearbox designed from the ground up for NEO-class motors. The design of the MAXPlanetary has been carefully optimized to provide torque density unavailable in FRC up until now. The...

An individual cartridge for the MAXPlanetary System. This cartridge is a 9:1 gear reduction.With a 9:1 reduction in a single stage cartridge you will save significant space and weight in your builds that demand the higher reduction!The MAXPlanetary...

An individual cartridge for the MAXPlanetary System. This cartridge is a 5:1 gear reduction. The MAXPlanetary System is a cartridge-based modular planetary gearbox designed from the ground up for NEO-class motors. The design of the MAXPlanetary has been...

An individual cartridge for the MAXPlanetary System. This cartridge is a 4:1 gear reduction. The MAXPlanetary System is a cartridge-based modular planetary gearbox designed from the ground up for NEO-class motors. The design of the MAXPlanetary has been...

An individual cartridge for the MAXPlanetary System. This cartridge is a 3:1 gear reduction. The MAXPlanetary System is a cartridge-based modular planetary gearbox designed from the ground up for NEO-class motors. The design of the MAXPlanetary has been...

The UltraPlanetary Gearbox Kit comes with UltraPlanetary Cartridges to support six different final gear reductions ranging from nominally 3:1 to 60:1 allowing for the right amount of torque for the application at hand. The kit has a pinion already...

With an efficient right-angle configuration, the Ultra 90 Degree Gearbox offers a robust solution to building a more compact robot. The Ultra 90 Degree Gearbox allows you to connect the UltraPlanetary Gearbox and the HD Hex Motor (REV-41-1600)...

20DP Gears are compatible with the REV ION System and come in a wide range of sizes and bores. Larger gears feature #10 clearance holes arranged in a 2-inch bolt circle pattern and MAXTube mounting pattern. A notch on the bore provides an easy...

20DP Gears are compatible with the REV ION System and come in a wide range of sizes and bores. Larger gears feature #10 clearance holes arranged in a 2-inch bolt circle pattern. A notch on the bore provides an easy visual indicator to ensure gears on the...

The MAXSpline Shaft is compatible with the REV ION System. The shaft is an extruded aluminum MAXSpline that provides a high strength alternative to 1/2in hex shaft that can interface with any REV ION System components with a MAXSpline bore. The...

ION #25 Sprockets are compatible with the REV ION System and designed for use with #25 Roller chain. #25 Plate Sprockets: Featuring MAXSpline and a 2in bolt circle that patterns outward radially, allowing for bolting to structure easily. #25 Hub...

Dead Axle Tube is compatible with the REV ION System and can be used with 3/4in Needle Bearing Carrier (REV-21-2385) and MAXSpline Shaft (REV-21-2520) as the dead axle in a dead axle roller. Can also be used with custom rollers and as...

MAXHubs are compatible with the REV ION System and provide a way to transfer torque to a MAXSpline bore from shafts of various shapes and sizes. Other hub variants allow for other bores or mount holes to populate within an existing MAXSpline...

The 1in Pivot Joint is compatible with the REV ION System. Create a pivot joint at the end of a piece of MAXTube - 1x1 with Grid Structure. Specifications Material: POM (Acetal/Delrin) Documentation ION Build System Guide Introduction to...

#10-32 Standoffs are compatible with the REV ION System and provide spacing for mounting key items on your robot. These standoffs are tapped on each end for a #10-32 thread and have a 3/8in flat to flat dimension, similar to a #10-32 nut...

Ratio Plates are compatible with the REV ION System. When you need a ratio other than 1:1, Ratio Plates make it easy to position sprockets and pulleys at the perfect center-to-center distance for the given ratio and length of #25 chain or RT25 belt...

1/2in Rounded Hex Shafts are compatible with the REV ION System and are a ready-to-use length of hex shaft that have been cut to length and have the ends tapped. The ends are tapped #10-32 in order to accept a screw and washer or shaft collar. The 1/2in...

#10 Spacers are compatible with the REV ION System and are an accurate way to space structural components like plates, brackets, or tubes apart on #10 screws. Can also be used to to space motion components like gearboxes away from their mounting...

ION Grip Wheels are compatible with the REV ION System and come in a wide range of sizes, durometers, and bores. Larger wheels contain the MAXSpline bore, but can be adapted to other bores with a separate MAXHub. Wheels with spokes have a bolt...

ION Traction Wheels are compatible with the REV ION System and come in a wide range of sizes, durometers, and bores. Larger wheels contain the MAXSpline bore, but can be adapted to other bores with a separate MAXHub. Wheels with spokes have a bolt circle...

ION Omni Wheels are compatible with the REV ION System and come in a wide range of sizes, all featuring the MAXSpline bore. Other bores are possible with a separate MAXHub. Rollers for each wheel size are unique, which ensures perfectly circular wheels...

ION Compliant Wheels are compatible with the REV ION System and come in a wide range of sizes, durometers, and bores. Larger wheels contain the MAXSpline bore, but can be adapted to other bores with a separate MAXHub. The radial spoke profile allows for...

MAXSpline Spacers are compatible with the REV ION System and can be used on the shaft as a spacer; they also work as spacers between wheels and sprockets, etc. The MAXSpline Spacer with MAX Pattern features a 2in bolt circle pattern.  Specifications...

1/2in Hex Shaft Spacers are compatible with the REV ION System and can be used on the shaft as a spacer; they also work as spacers between wheels and sprockets, etc. Specifications Material: POM (Acetal/Delrin) OD: 0.72in Weights & Dimensions: ...

MAXSpline Spacers are compatible with the REV ION System and can be used on the shaft as a spacer; they also work as spacers between wheels and sprockets, etc. Specifications Material: POM (Acetal/Delrin) OD: 1.50in Weights &...

Experience a significantly longer lifespan with the 3in MAXSwerve Plastic Wheel V2.0, designed for the 3in MAXSwerve Module. Now crafted from Glass-Filled Nylon/PP & TPR, it boasts a more rigid rubber tread for increased durability without...

The MAXLift #25 Chain Attachment Plate is a durable yet lightweight aluminum bracket designed for seamless use with the REV ION system within the MAXLift family of products. It simplifies mounting and assembly for elevator and lift systems. Featuring...

The 3in MAXSwerve Module - Kraken Input Kit is a versatile add-on designed to integrate the Kraken X60 motor with the 3in MAXSwerve Module. This kit features a modified 14T pinion gear for seamless power transfer with the 8mm - 15T spline. It includes a...

The MAXPlanetary Kraken X44 & Minion Input Kit is a comprehensive solution for adapting Kraken X44 or Minion motors to the MAXPlanetary system. This kit includes the [REV-21-4444] MAXPlanetary Kraken X44 & Minion Adapter Plate, designed with...

The MAXLift Bearing Blocks are integral components of the MAXLift system, providing teams with a robust and space-efficient solution for building high-performance elevator assemblies. With the main blocks being designed around billet aluminum...

GT2 3mm Pitch Belts are compatible with both the REV ION System and the REV DUO System. These belts go hand in hand with GT2 timing pulleys. Use belts and pulleys in tight to fit areas where adjustment is difficult. Specifications Pitch: 3mm Width:...

Bearings 1/2in Hex Bearing - Flanged - 1.125in OD - 4 Pack (REV-21-1915-PK4) This flanged bearing provides a reliable way to locate and support a 1/2in hex shaft or 1/2in rounded hex shaft while it rotates. The flange ensures secure installation in...

#10-32 Shaft End Screw V1 and V2 are compatible with the REV ION System and are used to retain parts on any ION hex shaft instead of shaft collars. 1/2in Rounded Hex Shafts in various lengths are available and come tapped with #10-32 holes. The...