Competition

The Molex MicroFit+ Power and CAN Cable is the dedicated replacement and accessory cable for the MAXSpline Through Bore Encoder. It provides both power and CAN connectivity through a compact, secure 2x2 Molex MicroFit+ latching connector. While currently...

The 1in Basic Corner Bracket is a compact, low profile solution for strengthening MAXTube joints or adding simple mounting points where space is limited. Its 5mm thick aluminum construction provides dependable stiffness without the added bulk of a...

The 1in Angled Corner Bracket is a compact, heavy duty solution for reinforcing MAXTube joints and building rigid structures in tight spaces. Its 5mm thick aluminum body provides consistent strength, while the integrated angle dramatically boosts joint...

The Locking Shaft Collar MAXSpline is a compact, purpose built clamping solution for securing components to a MAXSpline shaft. Designed as a thin aluminum plate, it can be paired with a second collar or mounted directly to any MAXSpline wheel or sprocket...

The Locking MAXHub - 1/2in Hex Kit is a compact, dual plate hub system designed to secure 1/2in hex shafting inside any MAXSpline bore component. Each kit includes two identical wedge locking plates and the necessary #10-32 hardware. When the plates are...

The Adjustable Tube Mount is a precision machined aluminum bracket designed to give teams fine control over how 2x1 MAXTube attaches to robot structure. Three center counterbored holes allow a MAXTube Endcap to bolt on flush, creating a clean mounting...

The MAXPlanetary Universal Input Stage V2 is a redesigned mounting solution for integrating a wide range of FRC motors into the MAXPlanetary System. Built as the next evolution of the original universal input stage, V2 enhances strength, expands motor...

The CAN Terminator Pack provides two compact, plug-ready termination options for teams looking to maintain reliable CAN bus performance anywhere in their robot’s wiring. Each terminator uses a small 10mm x 10mm internal circuit board sealed with...

The ION Conveyor Brush System is a customizable solution for creating wide to narrow intake brushes that adapt to a variety of game pieces. The 24in brush can be cut to any length using a bandsaw or hacksaw, allowing teams to fine tune coverage and...

The ION Round Belt System provides a simple and adaptable way to transfer power in compact robot mechanisms. Designed around a 2in outer diameter when the belt is installed, the system stays on pitch with the REV ION wheel lineup, making it easy to...

The 8mm Shaft Spacer is a stainless steel 1/16 inch washer designed for precise shaft spacing in FRC and FTC mechanisms. Used on the NEO 2.0 Brushless Motor to achieve correct input coupler alignment in MAXPlanetary assemblies, this spacer also fits any...

The MAXPlanetary MAXSpline Output Coupler [REV-21-3630] provides a compact and reliable way to interface a MAXPlanetary Gearbox’s 1/2 inch hex output with MAXSpline Shaft systems. Designed for teams who want the packaging efficiency of a...

The NEO 2.0 Sensor Cable connects the NEO 2.0 Brushless Motor’s sensor port to a standard JST PH 6-pin interface used on REV motor controllers. The 2x3-pin PHSD connector provides a secure, latching connection at the motor, while the 6-pin JST PH...

ION Cone Wheels are designed to give teams controlled, predictable vectoring for game pieces and objects. Their tapered profile naturally guides items toward the smaller diameter, making them especially effective in intake edge zones and in-feed...

The 4in Spiky Wheel Tread 8 Pack provides replacement treads for teams using the 4in Spiky Wheels on their EasySwerve-equipped robots. These injection molded TPU treads feature an aggressive spiked geometry designed to maximize traction on FRC carpet...

The 4in Spiky Wheel Aluminum Hub is a precision machined and balanced wheel hub designed for use with the 4in Spiky Wheel system and the 4in EasySwerve Module. Built from 6061 aluminum, this hub provides a strong and reliable foundation for high-traction...

20DP Gears are compatible with the REV ION System and come in a wide range of sizes and bores. This gear features a 15T spline bore for use with 15T spline shaft and motors like our NEO 2.0 Brushless Motor. A notch on the bore provides an easy visual...

The MAXSpline Grommet provides a simple way to route wires through MAXTube while preventing abrasion against bare aluminum. Made from pliable 60A rubber, it press-fits into the MAXSpline Bore on MAXTube with a 1/8 inch wall, creating a clean pass-through...

The 4in Spiky Wheel - Hub and Tread Bundle includes everything needed to outfit a full 4in EasySwerve drive with high-traction 4in Spiky Wheels and a complete set of replacement treads. The bundle contains four (4) precision machined aluminum hubs, eight...

The 15T Spline to 1/2in Hex Adapter provides a simple and reliable way to integrate motors with a 15T spline output shaft into mechanisms designed around 1/2in rounded hex. This adapter is ideal for teams looking to pair the NEO 2.0 Brushless Motor...

The 15T Spline Shaft is a solid stainless steel shaft sized at 480mm for long span applications or to be used as stock to cut custom length shafts. Its 15 tooth involute spline profile features an 8mm outer diameter and interfaces with the REV ION...

An individual cartridge for the MAXPlanetary System. This cartridge is a 2:1 gear reduction. The 2:1 cartridge expands MAXPlanetary ratio options, joining the 1:1 (no cartridge), 3:1, 4:1, 5:1, and 9:1 cartridges. With the addition of 2:1, teams can...

The Elevator Bearing Block (REV-20-2051) is a trusted choice for smooth sliding motion between two pieces of rectangular tubing. It mounts on the narrow, 1in side, of tubing (e.g. 1x1 or 2x1) and uses shielded ball bearings for reduced friction. Its...

The 550 Motor Pinions are used for transferring power from a 550 class motor, like the HD Hex Motor or NEO 550, to a mechanism. The Helical 550 Motor Pinion with 12 teeth is used exclusively with 20:1 and 40:1 Hex gearboxes ONLY...

The Through Bore Encoder V2 provides precise, reliable shaft position measurement with both incremental (ABI quadrature) and absolute (pulse-width) outputs. Its ½in hex through bore mounts easily within common FRC/FTC mechanisms, and the included...

Metal sprockets designed to work in high-load applications with #25 chain. This sprocket requires a hub like REV-41-1719. Specifications Chain Size: #25 Material: 6061 Aluminum Documentation SprocketGuide BuildingGuide Product...

REV Building System also comes in a 15mm x 30mm square extrusion. The slots are designed to fit standard M3 hardware rather than expensive t-nuts. Use the 15mm x 30mm extrusion when more strength is needed for an application. For smaller applications the...

REV 45mm U Channel has a 45mm x 45mm square profile, and is designed to work seamlessly with existing REV 15mm Extrusion. It can be used in locations where additional torsion strength is required. On the sides of the channel is the Extended Motion...

REV 45mm x 15mm C Channel has a 45mm x 15mm rectangular profile, and is designed to work seamlessly with existing REV 15mm Extrusion. It can be used in locations where additional torsional strength is required. The 45mm wide side of the channel...

The UltraUSB Hub is designed specifically for use in competitive robotics, and gives you the ability to connect multiple USB devices to each other as well as replacing cables when damaged instead of needing to replace the whole hub. The UltraUSB Hub can...

These JST PH 6-pin Extension Cables are intended to extend the reach of sensor cables without having to cut and splice wires. Specifications REV-11-1275-PK4: Length: 90cm (35.5in) REV-11-3327: Length: 30cm (11.81in)

REV 45mm Flat Plate is a 45mm wide, bendable metal featuring the Extended Motion Pattern. This product is a piece that is 440mm long. The Extended Motion Pattern supports M3 hardware for attaching brackets, extrusion, and channel...

This 90 degree inside corner bracket (REV-41-1320-PK8) is used with the DUO Build System 15mm Extrusion. These plastic brackets have webbing to strengthen the corner and includes a set of alignment ribs designed to seat the bracket into the extrusion...

REV Robotics custom ATO sized auto-resetting breakers are designed to give reliable protection for FRC robot actuators.  These custom developed breakers adhere to SAE Standard J553 and will give consistent performance even after hundreds of breaker...

This bearing pillow block bracket (REV-41-1317) is used with the DUO Build System 15mm Extrusion. The 9mm center hole is use with either the Long Through-bore Bearing (REV-41-1329) or the End Cap Bearing (REV-41-1322) to provide a low friction shaft...

Steel hardware of the appropriate size to work with the ION Build System 1in Extrusion. Length measured from tip to underside of screw head. Specifications Material: 18-8 Stainless Steel Diameter & Thread: #10-32 Length: 1/2in Documentation ION...

The REV M3 Nut Strip allows you to securely join plates and channels without the need for separate nuts. Simply thread bolts directly into the strip for fast and reliable assembly. Specifications Material: 6063 Aluminum Thread Pitch: M3 x 0...

Hex keys, also known as Allen wrenches or L-keys, are essential hand tools designed to drive screws and bolts with hexagonal recesses. They are widely used in robotics, engineering, and general assembly for tightening or loosening fasteners in compact or...

Designed specifically for the 2025 FIRST Global Challenge, this kit provides teams with the essential components needed to build a competitive and reliable robot. Packed with a carefully curated selection of mechanical, electrical, and control system...

The REV Smart Robot Servo V2 – available in Balanced and UltraSpeed configurations – is a fully configurable metal-geared servo designed to simplify servo-based mechanisms. Each SRS V2 can be used as a standard angular, custom angular, or...

Upgrade your 3in MAXSwerve Module with this high-performance motor and controller package, featuring the latest NEO Vortex Brushless Motor and SPARK Flex Motor Controllers. Created for maximum efficiency and advanced control, this bundle is perfect for...

Commonly included with our gearboxes and pinion options, the 8mm Keyed Shaft Retaining Hardware Pack is compatible with the REV ION System and includes the hardware needed to retain 2mm keyed elements to 8mm OD shafts without the bulk of alternative...

The MAXLift #25 Chain Attachment Plate is a durable yet lightweight aluminum bracket designed for seamless use with the REV ION system within the MAXLift family of products. It simplifies mounting and assembly for elevator and lift systems. Featuring...

The 3in MAXSwerve Module – 15T Spline Input Kit is designed to adapt the REV NEO 2.0 Brushless Motor or Kraken X60 for use with the 3in MAXSwerve Module. This kit provides the necessary gearing and hardware to integrate a 15T spline drive motor...

The MAXPlanetary Kraken X44 & Minion Input Kit is a comprehensive solution for adapting Kraken X44 or Minion motors to the MAXPlanetary system. This kit includes the [REV-21-4444] MAXPlanetary Kraken X44 & Minion Adapter Plate, designed with...

The MAXLift Bearing Blocks are integral components of the MAXLift system, providing teams with a robust and space-efficient solution for building high-performance elevator assemblies. With the main blocks being designed around billet aluminum...

GT2 3mm Pitch Belts are compatible with both the REV ION System and the REV DUO System. These belts go hand in hand with GT2 timing pulleys. Use belts and pulleys in tight to fit areas where adjustment is difficult. Specifications Pitch: 3mm Width: 9mm...

Bearings 15T Spline Bearing - Flanged - 1.125in OD - 4 Pack (REV-21-3294-PK4) Featuring a 8mm internal diameter and a 1.125in outer diameter, this bearing is designed to fit into a MAXSpline bore while supporting a 15T Spline shaft. The flange adds a way...