REV DUO

These small connectors can be used to join two JST PH 4-pin Sensor Cables to create a longer cable. 

The 2-pin JST VH Cable is keyed and locking for improved reliability.  Expansion Hub 2-pin JST VH Connections: Motor Power Product Options  SKU   PRODUCT NAME   REV-31-1412-PK4   JST VH 2-pin Motor Cable -...

The 4-pin JST PH Cable is keyed and locking for improved reliability.  Expansion Hub 4-pin JST PH Connections: Motor Encoder Digital Analog I2C Product Options  SKU   PRODUCT NAME   REV-31-1407-PK4   JST PH...

Charger for use with our 12V Slim Battery. The output is wired with an XT30 male connector for charging. For the input, the battery charger has an IEC C13 power cord to standard, grounded, North America wall outlet plug (NEMA 5-15). *Do not...

Add this switch between your battery and Expansion Hub to have convenient on/off control of your robot. We recommend mounting the switch slightly recessed from the outside of your robot so that it's not accidentally turned off by another robot during a...

Use the Anderson Power Pole to 2-pin JST VH Adapter Cable to connect your existing motors to the REV Robotics Expansion Hub. Teams that already own and use the Anderson Powerpole Crimper may purchase JST VH 2-pin Motor Cables (REV-31-1413), cut cables in...

The analog and digital ports on the Control Hub and Expansion Hub combine two sensor inputs into one connector to save space. Single sensors plugged directly into these ports will work, but they will block access to the second input. The Sensor Splitter...

Use these connectors to create your own custom length power wires. The XT30 Connector uses a solder cup instead of a crimping tool to connect the contact to a wire. 

Cross over cable to convert the pin out from Modern Robotic's I2C sensors to work with the REV Robotics's Logic Level Converter. 

High strength string for use with the small Pulley Bearings and the 15mm Linear Motion Kit to create a powered lift.   Specifications Material: Ultra-high-molecular-weight Polyethylene (UHMWPE) Load Rating: 300lb+ Diameter: 1.2mm...

8cm long Anderson Power Pole style connector to Female XT30 adapter cable used to covert team-modified battery connectors to the new XT30 connector.  Teams that already own and use the Anderson Powerpole Crimper may purchase XT30 Extension Cables...

8cm long Female Tamiya to Female XT30 adapter cable used to covert legacy battery connectors to the new XT30 standard. 

Touch sensor is best used for user input, but can also be used as a limit switch.  Configuration The REV Touch Sensor is a digital sensor that is wired to the N+1 channel on our standard 4-pin JST PH connector. In other words, the REV Expansion Hub...

The REV Robotics Logic Level Converter is a circuit board which generates a 5V output from the 3.3V input and uses a MOSFET on each signal line to create a bidirectional communication appropriate for a variety of digital signals include I2C communication...

This battery plate is the perfect size to support a REV 12v Battery, REV Control Hub, or REV Expansion Hub. CAD & Drawings REV-41-1166 STEP File REV-41-1166 Onshape REV-41-1166 Drawing  

The MiniBot Hardware Kit is a fast robot build ideal for basic programming training. Add control system components (REV-31-1595 Control Hub, REV-31-1596 Driver Hub, REV-31-1302 12V Slim Battery) and let your programming skills grow.  Kit...

Nylon Zip Ties with rounded edges to prevent snagging. Length is idea for cable management and many other uses. Specifications 160mm long Quality nylon construction 18lb. tensile strength

Double-sided hook and loop tape allows you to cut to desired custom lengths. Reusable, secure hold. Specifications 13.5mm width x 2m length

12-point combination wrench for use with M3 hardware. Specifications Chrome vanadium steel 5.5mm  15° angled ring head

Use these barbs with our Polyurethane Hollow Belt to join the ends and make custom length belts quickly and easily.  CAD & Drawings REV-41-1165 Drawing

Our Polyurethane Hollow Round Belting is perfect for your conveyor, and intake mechanisms. Use Barbs to assemble custom length belts. 

This stretchy latex rubber tubing is sized to fit through any of the M3 holes in DUO brackets, wheels, gears or other motion products. String tubing between outside holes on two wheels to create a compliant intake.  Specifications Color:...

This 10K potentiometer can be used as an analog sensor with the Control Hub or Expansion Hub. This potentiometer has a 270 degree range of motion and can be mounted to any REV DUO brackets with the Motion Pattern, like the Motion Bracket. The...

The REV Robotics Expansion Hub is a low-cost educational device that can communicate with any computer (commonly the REV Robotics Control Hub or an Android Phone) to provide the interfaces required for building robots and other mechatronics. The...

PWM Cables, which are used for connecting things like the SPARK Motor controller to the roboRIO. These can also be used as servo extension cables for getting signal and power a bit farther away than integrated wires can reach. Specifications Length:...

The Servo Power Module is a 6V 90W power injector that enables the use of high-power RC servos in applications where a robot controller cannot directly provide adequate power.  The Servo Power Unit passes through input signals unaltered while...

This gearbox is the same one used on our HD Hex Motor 40:1 Spur Gearbox featuring our 5mm HEX output shaft! This gearbox can be installed on any 550 series motors (like the NeveRest motors from AndyMark) giving you the convenience and...

These v-groove bearing pulleys fit on an M3 x 16mm Hex Cap Screw and can be mounted directly onto extrusion. Use with 15mm Linear Motion Kits and a high tensile strength no-stretch string, such as kevlar string or spectra fishing line, to create an...

Single Strand #25 roller chain for use with #25 sprockets. Use a master link (connecting link) for #25 chain connect two ends of chain to create a loop. Specifications Material: Steel Size: #25 Pitch: 0.25in

Master link (connecting link) for #25 chain. Use a master link to connect two ends of chain to create a loop. Specifications Material: Steel Size: #25 Pitch: 0.25in CAD & Drawings REV-41-1366 STEP File REV-41-1366 Onshape

Zinc plated steel nuts compatible with all REV M3 screws or bolts. Contains a nylon insert which increases grip on screw, reducing the chance of the nut loosening over time. Does NOT fit in the channel of our REV DUO 15mm Extrusion System...

Small electronics sized 5.5mm Nut Driver with rubberised grip fits M3 hex cap bolts and nuts. Specifications Socket Depth: 15.8mm Dimensions: 16.2cm x 2cm x 2cm (6.38in x 0.79in x 0.79in) Weight: 33g (1.16oz)

This 10-cell, 12V 3000mAh battery has a low profile configuration to make it easier to mount on a robot. The Slim Battery pack is wired with an XT30 male connector and an inline 20A replaceable ATM fuse. XT30 to Tamiya Adapter no longer automatically...

This shaft collar is compatible with the DUO Build System and is used to prevent gears, sprockets, wheels, and other parts from sliding out of place on a 5mm hex shaft. Shaft collars can also be used to prevent the shaft itself from sliding out of its...

This Servo Gear Adapter is a 15 Tooth Plastic Gear that attaches to any 25T output servo including the Smart Robot Servo. Warning: Gears from other building systems may have a very similar tooth profile but are not an exact match. It may be possible to...

The Servo Shaft Adapter makes it possible to drive a 5mm hex shaft with any 25T output servo including the Smart Robot Servo. The adapter attaches to the servo spline like any common servo horn and accepts a 5mm hex shaft on the opposite end...

The End Cap Bearing is used with the 5mm hex shaft recommended for the DUO Build System 15mm Extrusion to provide a low friction rotating shaft support. This bearing is intended to seat in any of the plastic REV DUO brackets with the 9mm ID bearing seat...

This lap corner bracket is used with the DUO Build System 15mm Extrusion. These plastic brackets have webbing to strengthen the corner and includes a set of alignment ribs on one side designed to seat the bracket into the extrusion channel increasing...

This 90 degree inside corner bracket is used with the DUO Build System 15mm Extrusion. These plastic brackets have webbing to strengthen the corner and includes a set of alignment ribs designed to seat the bracket into the extrusion channel increasing...

This bearing pillow block bracket is used with the DUO Build System 15mm Extrusion. The 9mm center hole is use with either the Long Through-bore Bearing (REV-41-1329) or the End Cap Bearing (REV-41-1322) to provide a low friction shaft support. This...

This bearing pillow block bracket is used with the DUO Build System 15mm Extrusion. The hex center hole fits the 5mm hex shaft. This bracket has alignment ribs on the bottom which help align the bracket with the extrusion channel...

For smaller applications the DUO Build System also comes in a 15mm x 15mm square extrusion. The 15mm profile of the 15mm Extrusion has slots on on all four sides that accept standard M3 hardware. Rather than using a T-nut, which is more expensive, slide...

The REV Smart Robot Servo (SRS) is a configurable metal-geared servo that takes the guesswork out of aligning and adjusting servo based mechanisms. One SRS can be used as a standard angular servo, a custom angular servo, and a continuous rotation servo...

The HD Hex series motors and gearboxes feature integrated encoders and power that plug right into the Control Hub (REV-31-1595) and Expansion Hub (REV-31-1153). The gearbox options feature 5mm Hex output or coupler making it easy to connect gears,...

For smaller applications the REV Building System also comes in a 15mm x 15mm square extrusion. The slots are designed to fit standard M3 hardware rather than expensive t-nuts. This product is a 2-pack of 120mm pieces of extrusion, for when you...

REV Building System also comes in a 15mm x 30mm square extrusion. The slots are designed to fit standard M3 hardware rather than expensive t-nuts. Use the 15mm x 30mm extrusion when more strength is needed for an application. Features All holes can be...

REV 45mm U Channel has a 45mm x 45mm square profile, and is designed to work seamlessly with existing REV 15mm Extrusion. It can be used in locations where additional torsion strength is required. On the sides of the channel is the Extended Motion...

The Through Bore Encoder is specifically designed with the end user in mind, allowing teams to place sensors in the locations closest to the rotation that they wish to measure. This rotary sensor measures both relative and absolute position through its...

This 8mm x 12mm x 3.5mm Flanged Bearing, when paired with the 5mm Hex to 8mm Round Bearing Insert (REV-41-1528), allows teams to support our 5mm hex shaft with a robust low friction bearing.   We recommend mounting the bearing into...

The Core Hex Motor is compatible with the DUO Build System and features a 90 degree orientation and a female output shaft for maximum flexibility and ease of use. Insert any of the REV standard 5mm Hex Shafts into or through the Core Hex Motor to create...

M3 Ball Joint Rod Ends are compatible with the REV DUO System. The Female M3 Ball Joint Rod End (REV-49-1560) can either be paired with its male counterpart to create short linkage arms or with M3 threaded rod and a second female ball...

Made to fit sockets that are found in various REV kits like the FTC Starter Kit V3 and the EDU Kit V2. Kit Contents  *exact product may vary from photo shown  SKU  PRODUCT NAME  PRODUCT QUANTITY  PACK...

The UltraPlanetary Female 5mm Output V2 is the output stage of the UltraPlanetary System. With two different ways to transfer power, the output stage allows designers to choose the option best suited for the application. The V2 version of the...

*This product has been replaced with the UltraPlanetary Female 5mm Hex Output V2 (REV-41-1615).  The REV UltraPlanetary Female 5mm Output is the output stage of the REV UltraPlanetary system. With two different ways to transfer power, the output...

This Servo Shaft Adapter makes it possible to drive a 5mm hex shaft with any 25T output servo including the Smart Robot Servo. The adapter attaches to the servo spline like any common servo horn and accepts a 5mm hex shaft on the opposite end. This...

This 5V WS2812B Addressable RGB LED Strip is compatible with the REV Blinkin LED Driver (REV-11-1105). Each LED contains an integrated driver IC and three LEDs; a red, green, and blue LED. Each individual LED can be controlled to create colorful patterns...

This 12V RGB LED Strip is compatible with the REV Blinkin LED Driver (REV-11-1105). Each LED on the strip is wired in parallel and actually contains three embedded LEDs; a red, green, and blue LED. Each color can be controlled separately to create any...

The Magnetic Limit Switch is a three-sided active-low digital hall effect switch with three internal hall effect elements located on the top and sides of the sensor. The three elements are connected in parallel so that any one of them will trigger the...

The REV Robotics SRS Programmer is the key to unlocking all the smart features of the (SRS) Smart Robot Servo (sold separately). Switching between continuous rotation, standard servo, and custom angular modes is easy as pressing a button...

The HD Hex series motors and gearboxes feature integrated encoders and power that plug right into the Control Hub (REV-31-1595) and Expansion Hub (REV-31-1153). The gearbox options feature 5mm Hex output or coupler making it easy to connect gears,...

These plastic 15mm Extrusion Slot Covers are ideal for making any machine look great!  COLOR  SKU  Red  REV-41-1633  White  REV-41-1634  Blue  REV-41-1635  Yellow  REV-41-1636  Green...

The HD Hex series motors and gearboxes feature integrated encoders and power that plug right into the Control Hub (REV-31-1595) and Expansion Hub (REV-31-1153). The gearbox options feature 5mm Hex output or coupler making it easy to connect gears,...

The UltraPlanetary 1/2in Hex Adapter is designed to face mount to the UltraPlanetary gearbox and provide a convenient 1/2in hex output shaft that is commonly used in the FIRST Robotics Competition. The recommended hardware for mounting the...

The 2.5mm WERA Hex-Plus L-Key is an allen wrench that fits any socket head M3 screw, such as the screws used to assemble the gearbox of the UltraPlanetary Gearbox Kit & HD Hex Motor. Long-arm hex keys offer extended reach for enhanced...

The 2.0mm WERA Hex-Plus L-Key is an allen wrench that fits any button head or flat M3 screw, such as those used to attach the gearbox to the motor body in the UltraPlanetary Gearbox Kit & HD Hex Motor, or those used to fasten slides to...

The 1.5mm WERA Hex-Plus L-Key is an allen wrench that fits M3 set screws, such as those used with Shaft Collars, Slim Shaft Collars, and the output stage of the UltraPlanetary Gearbox Kit & HD Hex Motor. Long-arm hex keys...

These are the same inserts that are included with the Through Bore Encoder.  Specifications Weight(s):  3/8in Hex: 23.5g (0.051lbs) 5mm Hex: 24.0g (0.052lbs) 1/4in Round: 24.0g (0.052lbs) Kit Contents QTY 1 - 3/8in Hex to 1/2in Hex...

This is all of the hardware included in the 15mm Linear Motion Kit V2 (REV-45-1507). Specifications Hole Diameter: M3 Clearance Kit Contents QTY 8 - M3 x 8mm Low Profile Socket Screws QTY 8 - M3 x 8mm Hex Cap Screws QTY 8 - M3 Nyloc Nuts QTY 8 - M3...

Aluminum Servo Arm that is compatible with the REV Smart Robot Servo. Lightweight and strong, this arm is best utilized under high and low torque applications. Specifications Material: 6061 Aluminum CAD & Drawings SKU-STP REV-41-1820...

The UltraPlanetary 550 Motor Plate works with the REV HD Hex Motor, REV NEO 550 Brushless Motor, and other 550 class motors. The UltraPlanetary System offers a variety of mounting options, with four different brackets available for attachment to REV...

This 12-point ratcheting combination wrench is perfect for fitting into those small spaces on your robot. For use with M3 hardware. Specifications Material: Chrome Vanadium Steel

This Metal HD Inside Corner bracket is used with the REV DUO 15mm Extrusion System for heavy duty applications. Specifications Material: 6063 Aluminum CAD & Drawings REV-41-1688 STEP File REV-41-1688 Onshape REV-41-1688 Drawing

The REV Robotics Slim Shaft Collar is used to prevent gears, sprockets, wheels, and other parts from sliding out of place on a 5mm hex shaft when space is at a premium. Shaft collars can also be used to prevent the shaft itself from sliding out of its...

The UltraUSB Hub is designed specifically for use in competitive robotics, and gives you the ability to connect multiple USB devices to each other as well as replacing cables when damaged instead of needing to replace the whole hub. The UltraUSB Hub can...

Make driving linear motion easy with the 22 Tooth Plastic Right Angle Rack Gear. Mount the rack gear to a slot in either the REV DUO Extrusion or REV DUO Channel while using any of the REV DUO Plastic Gears to drive motion. Specifications Module: 0...

DUO Grip Wheels are wider than our standard wheels, giving teams more traction while still being lightweight and robust. This wheel is compatible with 5mm hex shaft, which completely eliminates the need for expensive hubs or using potentially unreliable...

This metal Inside Corner bracket is used with the REV 15mm Extrusion System. Version 2 brackets offer many improvements over our previous metal brackets, including holes on an 8mm grid that is compatible with many other building systems. Version 2...

This metal ball bearing mount bracket is used with the REV DUO System 15mm Extrusion. Version 2 brackets offer many improvements over our previous metal brackets, including holes on an 8mm grid that is compatible with many other building systems. This...

The 5.5mm WERA Socket Screw Driver is for use with M3 hex head screws and nuts. Kraftform Ergonomic Micro handle design features the shape that facilitates high torque transfer and precision feel for fine adjustment work,...

The Universal Hex Adapter V2 is a steel hub that allows teams to quickly and easily adapt their existing parts to work with 5mm hex.  Specifications Material: Sintered Steel Hole Pattern: Four M3 tapped holes on a 0.630in (16mm) diameter circle -...

The Locking Motion Hub places a motion pattern on any 5mm hex shaft. Use this to connect metal sprockets to 5mm hex shaft or add strength to wheels, gears, and plastic sprockets through the REV Motion Pattern without the need of a shaft collar...

This metal Hex Bearing Block is used with the REV DUO 15mm Extrusion and REV DUO Channel. A hex ball bearing is pre-pressed into the metal bracket. Specifications Material: Sintered Steel, Steel CAD & Drawings SKU-STP REV-41-1683 Onshape SKU-DR

REV 45mm x 15mm C Channel has a 45mm x 15mm rectangular profile, and is designed to work seamlessly with existing REV 15mm Extrusion. It can be used in locations where additional torsional strength is required. The 45mm wide side of the channel...

The HD Hex Spur Gearbox Spacer V2 makes it easier to use the Motion Pattern for mounting HD Hex Motors with a Spur Gearbox. Specifications Material: ABS Documentation DUO Build System Guide CAD & Drawings REV-41-1648 STEP File REV-41-1648...

Universal Hex Adapter (REV-41-1833) also available as an alternative. This part is a replacement for the discontinued Hex Hub Adapter (REV-41-1146). Expand your team's building options without giving up the products that you already own. This sintered...

Timing belts and pulleys are compatible with the REV DUO System. They are lighter and can be more efficient than chains and sprockets. Tensioning and adjustment are a thing of the past. 24 Tooth through 60 Tooth size pulleys come with two ends and an...

The UltraUSB Hub Power to USB A Cable is used to power the UltraUSB Hub off a 5V external battery pack with USB A connectors.  Documentation UltraUSB Hub Quick Start Guide

The UltraUSB Hub Power to PWM Cable is used to power the UltraUSB Hub off the 5V rail on the REV Expansion Hub or Control Hub.  Documentation UltraUSB Hub Quick Start Guide

The UltraUSB Hub Upstream to USB A Cable is a data cable used to connect the UltraUSB Hub to any USB-A device, like a laptop. Documentation UltraUSB Hub Quick Start Guide

The UltraUSB Hub Upstream to USB Micro-B OTG Cable is a data cable used to connect the UltraUSB Hub to a micro-USB phone. Documentation UltraUSB Hub Quick Start Guide

This product is no longer in production and is only available as long as supplies last. This product has been replaced with Color Sensor V3 (REV-31-1557). Version 3 of the REV Color Sensor introduces a new sensor chip by Broadcom due to...

This cable is for use with the Blinkin LED Driver. This cable converts the JST PH 7-pin connector on the Blinkin' LED Driver module to a males 3-pin JST SM and male 4-pin JST SM connectors for connecting 5V WS2812 addressable LED and 12V RGB LED strips...

When designing chain or belt driven system, the ability to adjust tension in the system is ideal. Using the Tensioning Bushing with REV DUO U Channel allows users to fine tune their system to find the optimum amount of tension for any application...

M3 standoffs are compatible with the REV DUO System and are perfect for raising one assembly above another or as linkages when paired with male ball joint rod ends (REV-49-1561). Specifications Material: 6063 Black Anodized Aluminum Thread...

Metal sprockets designed to work in high-load applications with #25 chain. This sprocket requires a hub like REV-41-1719. Specifications Chain Size: #25 Material: 6061 Aluminum Documentation SprocketGuide BuildingGuide CAD &...

Metal sprockets designed to work in high-load applications with #25 chain. This sprocket requires a hub like REV-41-1719. Specifications Chain Size: #25 Material: 6061 Aluminum Documentation SprocketGuide BuildingGuide CAD &...