Filter By
- Product
- Qty in Cart
- Quantity
- Price
- Subtotal
-
Blinkin LED Driver
REV-11-1105$49.68Blinkin makes adding LEDs to your robot as simple as driving a motor. Chose the pattern you want and give it the corresponding PWM signal. The REV Blinkin LED Driver is a compact LED driver module... -
Touch Sensor
REV-31-1425$8.75Touch sensor is best used for user input, but can also be used as a limit switch. Configuration The REV Touch Sensor is a digital sensor that is wired to the N+1 channel on our standard 4-pin JST PH... -
36in 2-Wire Jumper Cable
REV-11-1134$2.502-pin header cable that can be used for connecting signals, sensors or any other spots on robots. Features 2 female 0.1in pitch connectors on each end. Specifications Length: 91cm (36in) 2 pin... -
Through Bore Encoder V1
REV-11-1271$48.00$40.80The Through Bore Encoder V1 allows teams to place sensors in the locations closest to the rotation that they wish to measure. This rotary sensor measures both relative and absolute position through... -
4-Pin JST to PWM Sensor Adapter Cable - 2 Pack
REV-11-1292-PK2$4.50The REV 4-Pin JST to PWM Sensor Adapter Cable allows for seamless connection of REV Robotics Sensors like the Magnetic Limit Switch and Potentiometer to the FRC Control System. Please note that this... -
5V Addressable LED Strip - 1m
REV-11-1198$26.00This 5V WS2812B Addressable RGB LED Strip is compatible with the REV Blinkin LED Driver (REV-11-1105). Each LED contains an integrated driver IC and three LEDs; a red, green, and blue LED. Each... -
12V RGB LED Strip - 5m
REV-11-1197$28.75This 12V RGB LED Strip is compatible with the REV Blinkin LED Driver (REV-11-1105). Each LED on the strip is wired in parallel and actually contains three embedded LEDs; a red, green, and blue LED... -
Magnetic Limit Switch
REV-31-1462$17.50The Magnetic Limit Switch is a three-sided active-low digital hall effect switch with three internal hall effect elements located on the top and sides of the sensor. The three elements are connected... -
Through Bore Encoder Insert Pack
REV-25-1870$4.00These are the same inserts that are included with the Through Bore Encoder. Specifications Weight(s): 3/8in Hex: 23.5g (0.051lbs) 5mm Hex: 24.0g (0.052lbs) 1/4in Round: 24.0g (0.052lbs) Kit... -
Analog Pressure Sensor
REV-11-1107$39.42The REV Robotics Analog Pressure Sensor is a 5V sensor that can measure pressures up to 200 PSI. It outputs an analog voltage that is proportional to the measured pressure and can plug directly into... -
MXP Extension Cable
REV-11-1118$17.00Extend the reach of your MXP port by using this 18" cable to reposition your boards where you need them. Fully compatible with all REV Robotics MXP accessory boards (More Board, Proto Board, &... -
Digit MXP Display
REV-11-1113$23.00The REV Robotics Digit is multi-use MXP board for interface with the roboRIO. It has four 12 segment displays, which can be used to show any letters or numbers. It also features an analog... -
Blinkin LED Cable Adapter
REV-11-1196$4.00This cable is for use with the Blinkin LED Driver. This cable converts the JST PH 7-pin connector on the Blinkin' LED Driver module to a males 3-pin JST SM and male 4-pin JST SM connectors for...