FIRST Tech Challenge

The REV Robotics Logic Level Converter is a circuit board which generates a 5V output from the 3.3V input and uses a MOSFET on each signal line to create a bidirectional communication appropriate for a variety of digital signals include I2C communication...

This battery plate is the perfect size to support a REV 12v Battery, REV Control Hub, or REV Expansion Hub. CAD & Drawings REV-41-1166 STEP File REV-41-1166 Onshape REV-41-1166 Drawing  

The MiniBot Hardware Kit is a fast robot build ideal for basic programming training. Add control system components (REV-31-1595 Control Hub, REV-31-1596 Driver Hub, REV-31-1302 12V Slim Battery) and let your programming skills grow.  Kit Contents...

Nylon Zip Ties with rounded edges to prevent snagging. Length is idea for cable management and many other uses. Specifications 160mm long Quality nylon construction 18lb. tensile strength

Double-sided hook and loop tape allows you to cut to desired custom lengths. Reusable, secure hold. Specifications 13.5mm width x 2m length

12-point combination wrench for use with M3 hardware. Specifications Chrome vanadium steel 5.5mm  15° angled ring head

Use these barbs with our Polyurethane Hollow Belt to join the ends and make custom length belts quickly and easily.  CAD & Drawings REV-41-1165 Drawing

Our Polyurethane Hollow Round Belting is perfect for your conveyor, and intake mechanisms. Use Barbs to assemble custom length belts. 

This stretchy latex rubber tubing is sized to fit through any of the M3 holes in DUO brackets, wheels, gears or other motion products. String tubing between outside holes on two wheels to create a compliant intake.  Specifications Color: Black...

This 10K potentiometer can be used as an analog sensor with the Control Hub or Expansion Hub. This potentiometer has a 270 degree range of motion and can be mounted to any REV DUO brackets with the Motion Pattern, like the Motion Bracket. The...

The REV Robotics Expansion Hub is a low-cost educational device that can communicate with any computer (commonly the REV Robotics Control Hub or an Android Phone) to provide the interfaces required for building robots and other mechatronics. The...

PWM Cables, which are used for connecting things like the SPARK Motor controller to the roboRIO. These can also be used as servo extension cables for getting signal and power a bit farther away than integrated wires can reach. Specifications Length:...

The Servo Power Module is a 6V 90W power injector that enables the use of high-power RC servos in applications where a robot controller cannot directly provide adequate power.  The Servo Power Unit passes through input signals unaltered while...

This gearbox is the same one used on our HD Hex Motor 40:1 Spur Gearbox featuring our 5mm HEX output shaft! This gearbox can be installed on any 550 series motors (like the NeveRest motors from AndyMark) giving you the convenience and...

These v-groove bearing pulleys fit on an M3 x 16mm Hex Cap Screw and can be mounted directly onto extrusion. Use with 15mm Linear Motion Kits and a high tensile strength no-stretch string, such as kevlar string or spectra fishing line, to create an...

Single Strand #25 roller chain for use with #25 sprockets. Use a master link (connecting link) for #25 chain connect two ends of chain to create a loop. Specifications Material: Steel Size: #25 Pitch: 0.25in

Master link (connecting link) for #25 chain. Use a master link to connect two ends of chain to create a loop. Specifications Material: Steel Size: #25 Pitch: 0.25in CAD & Drawings REV-41-1366 STEP File REV-41-1366 Onshape

Zinc plated steel nuts compatible with all REV M3 screws or bolts. Contains a nylon insert which increases grip on screw, reducing the chance of the nut loosening over time. Does NOT fit in the channel of our REV DUO 15mm Extrusion System. Specifications...

Small electronics sized 5.5mm Nut Driver with rubberised grip fits M3 hex cap bolts and nuts. Specifications Socket Depth: 15.8mm Dimensions: 16.2cm x 2cm x 2cm (6.38in x 0.79in x 0.79in) Weight: 33g (1.16oz)

This 10-cell, 12V 3000mAh battery has a low profile configuration to make it easier to mount on a robot. The Slim Battery pack is wired with an XT30 male connector and an inline 20A replaceable ATM fuse. XT30 to Tamiya Adapter no longer automatically...

This shaft collar is compatible with the DUO Build System and is used to prevent gears, sprockets, wheels, and other parts from sliding out of place on a 5mm hex shaft. Shaft collars can also be used to prevent the shaft itself from sliding out of its...

This Servo Gear Adapter is a 15 Tooth Plastic Gear that attaches to any 25T output servo including the Smart Robot Servo. Warning: Gears from other building systems may have a very similar tooth profile but are not an exact match. It may be possible to...

The Servo Shaft Adapter makes it possible to drive a 5mm hex shaft with any 25T output servo including the Smart Robot Servo. The adapter attaches to the servo spline like any common servo horn and accepts a 5mm hex shaft on the opposite end...

The End Cap Bearing is used with the 5mm hex shaft recommended for the DUO Build System 15mm Extrusion to provide a low friction rotating shaft support. This bearing is intended to seat in any of the plastic REV DUO brackets with the 9mm ID bearing seat...

This lap corner bracket is used with the DUO Build System 15mm Extrusion. These plastic brackets have webbing to strengthen the corner and includes a set of alignment ribs on one side designed to seat the bracket into the extrusion channel increasing...

This 90 degree inside corner bracket is used with the DUO Build System 15mm Extrusion. These plastic brackets have webbing to strengthen the corner and includes a set of alignment ribs designed to seat the bracket into the extrusion channel increasing...

This bearing pillow block bracket is used with the DUO Build System 15mm Extrusion. The 9mm center hole is use with either the Long Through-bore Bearing (REV-41-1329) or the End Cap Bearing (REV-41-1322) to provide a low friction shaft support. This...

This bearing pillow block bracket is used with the DUO Build System 15mm Extrusion. The hex center hole fits the 5mm hex shaft. This bracket has alignment ribs on the bottom which help align the bracket with the extrusion channel. Specifications ...

For smaller applications the DUO Build System also comes in a 15mm x 15mm square extrusion. The 15mm profile of the 15mm Extrusion has slots on on all four sides that accept standard M3 hardware. Rather than using a T-nut, which is more expensive, slide...

The REV Smart Robot Servo (SRS) is a configurable metal-geared servo that takes the guesswork out of aligning and adjusting servo based mechanisms. One SRS can be used as a standard angular servo, a custom angular servo, and a continuous rotation servo...

The HD Hex series motors and gearboxes feature integrated encoders and power that plug right into the Control Hub (REV-31-1595) and Expansion Hub (REV-31-1153). The gearbox options feature 5mm Hex output or coupler making it easy to connect gears,...

For smaller applications the REV Building System also comes in a 15mm x 15mm square extrusion. The slots are designed to fit standard M3 hardware rather than expensive t-nuts. This product is a 2-pack of 120mm pieces of extrusion, for when you...

REV Building System also comes in a 15mm x 30mm square extrusion. The slots are designed to fit standard M3 hardware rather than expensive t-nuts. Use the 15mm x 30mm extrusion when more strength is needed for an application. Features All holes can be...

REV 45mm U Channel has a 45mm x 45mm square profile, and is designed to work seamlessly with existing REV 15mm Extrusion. It can be used in locations where additional torsion strength is required. On the sides of the channel is the Extended Motion...

The Through Bore Encoder is specifically designed with the end user in mind, allowing teams to place sensors in the locations closest to the rotation that they wish to measure. This rotary sensor measures both relative and absolute position through its...

This 8mm x 12mm x 3.5mm Flanged Bearing, when paired with the 5mm Hex to 8mm Round Bearing Insert (REV-41-1528), allows teams to support our 5mm hex shaft with a robust low friction bearing.   We recommend mounting the bearing into...