Electronics

Touch sensor is best used for user input, but can also be used as a limit switch.  Configuration The REV Touch Sensor is a digital sensor that is wired to the N+1 channel on our standard 4-pin JST PH connector. In other words, the REV Expansion Hub...

The REV Robotics Logic Level Converter is a circuit board which generates a 5V output from the 3.3V input and uses a MOSFET on each signal line to create a bidirectional communication appropriate for a variety of digital signals include I2C communication...

This 10K potentiometer can be used as an analog sensor with the Control Hub or Expansion Hub. This potentiometer has a 270 degree range of motion and can be mounted to any REV DUO brackets with the Motion Pattern, like the Motion Bracket. The...

The REV Robotics Expansion Hub is a low-cost educational device that can communicate with any computer (commonly the REV Robotics Control Hub or an Android Phone) to provide the interfaces required for building robots and other mechatronics. The...

PWM Cables, which are used for connecting things like the SPARK Motor controller to the roboRIO. These can also be used as servo extension cables for getting signal and power a bit farther away than integrated wires can reach. Specifications Length:...

This 10-cell, 12V 3000mAh battery has a low profile configuration to make it easier to mount on a robot. The Slim Battery pack is wired with an XT30 male connector and an inline 20A replaceable ATM fuse. XT30 to Tamiya Adapter no longer automatically...

The Through Bore Encoder is specifically designed with the end user in mind, allowing teams to place sensors in the locations closest to the rotation that they wish to measure. This rotary sensor measures both relative and absolute position through its...

This 5V WS2812B Addressable RGB LED Strip is compatible with the REV Blinkin LED Driver (REV-11-1105). Each LED contains an integrated driver IC and three LEDs; a red, green, and blue LED. Each individual LED can be controlled to create colorful patterns...

This 12V RGB LED Strip is compatible with the REV Blinkin LED Driver (REV-11-1105). Each LED on the strip is wired in parallel and actually contains three embedded LEDs; a red, green, and blue LED. Each color can be controlled separately to create any...

The Magnetic Limit Switch is a three-sided active-low digital hall effect switch with three internal hall effect elements located on the top and sides of the sensor. The three elements are connected in parallel so that any one of them will trigger the...

These are the same inserts that are included with the Through Bore Encoder.  Specifications Weight(s):  3/8in Hex: 23.5g (0.051lbs) 5mm Hex: 24.0g (0.052lbs) 1/4in Round: 24.0g (0.052lbs) Kit Contents QTY 1 - 3/8in Hex to 1/2in Hex...

The UltraUSB Hub is designed specifically for use in competitive robotics, and gives you the ability to connect multiple USB devices to each other as well as replacing cables when damaged instead of needing to replace the whole hub. The UltraUSB Hub can...

The UltraUSB Hub Power to USB A Cable is used to power the UltraUSB Hub off a 5V external battery pack with USB A connectors.  Documentation UltraUSB Hub Quick Start Guide

The UltraUSB Hub Power to PWM Cable is used to power the UltraUSB Hub off the 5V rail on the REV Expansion Hub or Control Hub.  Documentation UltraUSB Hub Quick Start Guide

The UltraUSB Hub Upstream to USB A Cable is a data cable used to connect the UltraUSB Hub to any USB-A device, like a laptop. Documentation UltraUSB Hub Quick Start Guide

The UltraUSB Hub Upstream to USB Micro-B OTG Cable is a data cable used to connect the UltraUSB Hub to a micro-USB phone. Documentation UltraUSB Hub Quick Start Guide

This product is no longer in production and is only available as long as supplies last. This product has been replaced with Color Sensor V3 (REV-31-1557). Version 3 of the REV Color Sensor introduces a new sensor chip by Broadcom due to...

This cable is for use with the Blinkin LED Driver. This cable converts the JST PH 7-pin connector on the Blinkin' LED Driver module to a males 3-pin JST SM and male 4-pin JST SM connectors for connecting 5V WS2812 addressable LED and 12V RGB LED strips...