The Locking MAXHub - 1/2in Hex is a compact, dual plate hub system designed to secure 1/2in hex shafting inside any MAXSpline bore component. Each kit includes two identical wedge locking plates and the necessary #10-32 hardware. When the plates are...

The Adjustable Tube Mount is a precision machined aluminum bracket designed to give teams fine control over how 2x1 MAXTube attaches to robot structure. Three center counterbored holes allow a MAXTube Endcap to bolt on flush, creating a clean mounting...

The MAXPlanetary Universal Input Stage V2 is a redesigned mounting solution for integrating a wide range of FRC motors into the MAXPlanetary System. Built as the next evolution of the original universal input stage, V2 enhances strength, expands motor...

The CAN Terminator Pack provides two compact, plug-ready termination options for teams looking to maintain reliable CAN bus performance anywhere in their robot’s wiring. Each terminator uses a small 10mm x 10mm internal circuit board sealed with...

The ION Conveyor Brush System is a customizable solution for creating wide to narrow intake brushes that adapt to a variety of game pieces. The 24in brush can be cut to any length using a bandsaw or hacksaw, allowing teams to fine tune coverage and...

The ION Round Belt System provides a simple and adaptable way to transfer power in compact robot mechanisms. Designed around a 2in outer diameter when the belt is installed, the system stays on pitch with the REV ION wheel lineup, making it easy to...

The 8mm Shaft Spacer is a stainless steel 1/16 inch washer designed for precise shaft spacing in FRC and FTC mechanisms. Used on the NEO 2.0 Brushless Motor to achieve correct input coupler alignment in MAXPlanetary assemblies, this spacer also fits any...

The MAXPlanetary MAXSpline Output Coupler [REV-21-3630] provides a compact and reliable way to interface a MAXPlanetary Gearbox’s 1/2 inch hex output with MAXSpline Shaft systems. Designed for teams who want the packaging efficiency of a...

The Vortex Shaft - 20DP Gear - 8T is compatible with the REV ION System and offers users the unique ability to achieve substantial gear reductions directly from the motor. This gear features a 8T 20DP design that is typically too small for an 8mm keyed...

The NEO 2.0 Sensor Cable connects the NEO 2.0 Brushless Motor’s sensor port to a standard JST PH 6-pin interface used on REV motor controllers. The connector provides a secure, latching connection at the motor, while the JST PH 6-pin end maintains...

REV ION Cone Wheels are designed to give teams controlled, predictable vectoring for game pieces and objects. Their tapered profile naturally guides items toward the smaller diameter, making them especially effective in intake edge zones and in-feed...

The 4in Spiky Wheel Tread 8 Pack provides replacement treads for teams using the 4in Spiky Wheels on their EasySwerve-equipped robots. These injection molded TPU treads feature an aggressive spiked geometry designed to maximize traction on FRC carpet...

The 4in Spiky Wheel Aluminum Hub is a precision machined and balanced wheel hub designed for use with the 4in Spiky Wheel system and the 4in EasySwerve Module. Built from 6061 aluminum, this hub provides a strong and reliable foundation for high-traction...

20DP Gears are compatible with the REV ION System and come in a wide range of sizes and bores. This gear features a 15T spline bore for use with 15T spline shaft and motors like our NEO 2.0 Brushless Motor. A notch on the bore provides an easy visual...

The MAXSpline Grommet provides a simple way to route wires through MAXTube while preventing abrasion against bare aluminum. Made from pliable 60A rubber, it press-fits into the MAXSpline Bore on MAXTube with a 1/8 inch wall, creating a clean pass-through...

The 4in Spiky Wheel - Hub and Tread Bundle includes everything needed to outfit a full 4in EasySwerve drive with high-traction 4in Spiky Wheels and a complete set of replacement treads. The bundle contains four (4) precision machined aluminum hubs, eight...

The 15T Spline to 1/2in Hex Adapter provides a simple and reliable way to integrate motors with a 15T spline output shaft into mechanisms designed around 1/2in rounded hex. This adapter is ideal for teams looking to pair the NEO 2.0 Brushless Motor...

The 15T Spline Shaft is a solid stainless steel shaft sized at 480mm for long span applications or to be used as stock to cut custom length shafts. Its 15 tooth involute spline profile features an 8mm outer diameter and interfaces with the REV ION...

The Elevator Bearing Block (REV-20-2051) is a trusted choice for smooth sliding motion between two pieces of rectangular tubing. It mounts on the narrow, 1in side, of tubing (e.g. 1x1 or 2x1) and uses shielded ball bearings for reduced friction. Its...

The 550 Motor Pinions are used for transferring power from a 550 class motor, like the HD Hex Motor or NEO 550, to a mechanism. The Helical 550 Motor Pinion with 12 teeth is used exclusively with 20:1 and 40:1 Hex gearboxes ONLY...