REV ION

The Magnetic Limit Switch is a three-sided active-low digital hall effect switch with three internal hall effect elements located on the top and sides of the sensor. The three elements are connected in parallel so that any one of them will trigger the...

The REV Robotics SRS Programmer is the key to unlocking all the smart features of the (SRS) Smart Robot Servo (sold separately). Switching between continuous rotation, standard servo, and custom angular modes is easy as pressing a button...

This Eye-to-Eye Turnbuckle is ideal for tensioning string, cordage, or cabling in linear motion applications. The welded eyes provide significantly more strength than bent eyes. Specifications Material: Steel Thread: M5 Retracted Length: 106mm +-...

The 1in Extrusion Endcap Slide allows teams to create compact and robust multistage lifts when combined with the 1in Linear Motion Kit (REV-15-1189) and the 1in Extrusion (REV-21-1000). The slide tab is offset allowing stages to fully nest when collapsed...

High-strength and low-stretch cord that is ideal for actuating lifts and other linear mechanisms. Also known as Spectra or Dyneema, this cord type minimizes the need for adjustments and re-tensioning after first assembly due to its low-stretch properties...

For use with the ION Build System 1in Extrusion to create linear motion.   Kit Contents QTY 1 - REV-21-1032 - Dual Bearing Plate QTY 1 - REV-21-1029 - Eccentric Bushing QTY 1 - REV-21-1030 - Concentric Bushing QTY 2 -...

The UltraPlanetary 1/2in Hex Adapter is designed to face mount to the UltraPlanetary gearbox and provide a convenient 1/2in hex output shaft that is commonly used in the FIRST Robotics Competition. The recommended hardware for mounting the...

These are the same inserts that are included with the Through Bore Encoder.  Specifications Weight(s):  3/8in Hex: 23.5g (0.051lbs) 5mm Hex: 24.0g (0.052lbs) 1/4in Round: 24.0g (0.052lbs) Kit Contents QTY 1 - 3/8in Hex to 1/2in Hex...

Aluminum Servo Arm that is compatible with the REV Smart Robot Servo. Lightweight and strong, this arm is best utilized under high and low torque applications. Specifications Material: 6061 Aluminum CAD & Drawings SKU-STP REV-41-1820...

Eccentric bushings are used to hold our V-Groove Bearings (REV-29-1014) for linear motion applications. The hole is drilled off-center of the bearing axis so by rotating the bushing on its mounting bolt, the clearance between the wheel and track can...

This dual bearing plate holds two V-Groove Bearings (REV-29-1014) to create an easy linear motion system for the ION Build System 1in Extrusion (REV-21-1000). Using a combination of Concentric (REV-21-1030) and Eccentric (REV-21-1029) bushings, the user...

Concentric bushings are used to hold our V-Groove Bearings (REV-29-1014) for linear motion applications. Used in conjunction with our Eccentric Bushing (REV-21-1029), the user can adjust how tight or loose they would like to tune their linear...

The REV Robotics Analog Pressure Sensor is a 5V sensor that can measure pressures up to 200 PSI. It outputs an analog voltage that is proportional to the measured pressure and can plug directly into the roboRIO or the More Board V2.0...

The UltraPlanetary 550 Motor Plate works with the REV HD Hex Motor, REV NEO 550 Brushless Motor, and other 550 class motors. The UltraPlanetary System offers a variety of mounting options, with four different brackets available for attachment to REV...

Complete gear set replacement for the Smart Robot Servo (REV-41-1097) Notes Replacement Gear Sets purchased after 03/27/2019 ship with updated versions of the replacement gears that fit the updated version of the Smart...

Extend the reach of your MXP port by using this 18" cable to reposition your boards where you need them. Fully compatible with all REV Robotics MXP accessory boards (More Board, Proto Board, & RIOduino) Specifications Keyed male and female...

The REV Robotics Digit is multi-use MXP board for interface with the roboRIO. It has four 12 segment displays, which can be used to show any letters or numbers. It also features an analog potentiometer and two momentary buttons. Teams can use the...

The robust 1in Inside Corner Bracket is designed to enable more construction strategies with the REV 1in Extrusion (REV-21-1000). Designed for #10 hardware, the mounting holes are on a 1in pitch that allows for the creation of complex joints by...

Steel hardware of the appropriate size to work with the ION Build System 1in Extrusion. Length includes the flat screw head. Specifications Material: 18-8 Stainless Steel Diameter & Thread: #10-32 Length: 1/2in Documentation ION Build System...

Steel hardware of the appropriate size to work with the ION Build System 1in Extrusion. Length measured from tip to underside of screw head. Specifications Material: 18-8 Stainless Steel Diameter & Thread: #10-32 Length: 1/2in Documentation ION...

Steel hardware of the appropriate size to work with the ION Build System 1in Extrusion. Length measured from tip to underside of screw head. Specifications Material: 18-8 Stainless Steel Diameter & Thread: #10-32 Length: 3/8in Documentation ION...

These Low Profile Nylon Lock Nuts are thin enough to fit inside the channel of the ION Build System 1in Extrusion. The embedded nylon ring provides tight vibration resistant hold on the threads of the screw. Specifications Material: Zinc-plated...

This cable is for use with the Blinkin LED Driver. This cable converts the JST PH 7-pin connector on the Blinkin' LED Driver module to a males 3-pin JST SM and male 4-pin JST SM connectors for connecting 5V WS2812 addressable LED and 12V RGB LED strips...

M3 Hex Cap Screws are compatible with the REV DUO System. Length measured from tip to underside of hex cap. Specifications Material: Corrosion Resistant Zinc Plated Steel Thread Pitch: M3 x 0.5 Head Dimensions: 5.5mm Hex Width, 2mm...