Competition

The 15T Spline to 1/2in Hex Adapter provides a simple and reliable way to integrate motors with a 15T spline output shaft into mechanisms designed around 1/2in rounded hex. This adapter is ideal for teams looking to pair the NEO 2.0 Brushless Motor...

The 15T Spline Shaft is a solid stainless steel shaft sized at 480mm for long span applications or to be used as stock to cut custom length shafts. Its 15 tooth involute spline profile features an 8mm outer diameter and interfaces with the REV ION...

The Elevator Bearing Block (REV-20-2051) is a trusted choice for smooth sliding motion between two pieces of rectangular tubing. It mounts on the narrow, 1in side, of tubing (e.g. 1x1 or 2x1) and uses shielded ball bearings for reduced friction. Its...

The 550 Motor Pinions are used for transferring power from a 550 class motor, like the HD Hex Motor or NEO 550, to a mechanism. The Helical 550 Motor Pinion with 12 teeth is used exclusively with 20:1 and 40:1 Hex gearboxes ONLY...

The Through Bore Encoder V2 provides precise, reliable shaft position measurement with both incremental (ABI quadrature) and absolute (pulse-width) outputs. Its ½in hex through bore mounts easily within common FRC/FTC mechanisms, and the included...

Metal sprockets designed to work in high-load applications with #25 chain. This sprocket requires a hub like REV-41-1719. Specifications Chain Size: #25 Material: 6061 Aluminum Documentation SprocketGuide BuildingGuide Product...

REV Building System also comes in a 15mm x 30mm square extrusion. The slots are designed to fit standard M3 hardware rather than expensive t-nuts. Use the 15mm x 30mm extrusion when more strength is needed for an application. For smaller applications the...

REV 45mm U Channel has a 45mm x 45mm square profile, and is designed to work seamlessly with existing REV 15mm Extrusion. It can be used in locations where additional torsion strength is required. On the sides of the channel is the Extended Motion...

REV 45mm x 15mm C Channel has a 45mm x 15mm rectangular profile, and is designed to work seamlessly with existing REV 15mm Extrusion. It can be used in locations where additional torsional strength is required. The 45mm wide side of the channel...

The UltraUSB Hub is designed specifically for use in competitive robotics, and gives you the ability to connect multiple USB devices to each other as well as replacing cables when damaged instead of needing to replace the whole hub. The UltraUSB Hub can...

These JST PH 6-pin Extension Cables are intended to extend the reach of sensor cables without having to cut and splice wires. Specifications REV-11-1275-PK4: Length: 36in REV-11-3327: Length: 30cm

REV 45mm Flat Plate is a 45mm wide, bendable metal featuring the Extended Motion Pattern. This product is a piece that is 440mm long. The Extended Motion Pattern supports M3 hardware for attaching brackets, extrusion, and channel...

This 90 degree inside corner bracket (REV-41-1320-PK8) is used with the DUO Build System 15mm Extrusion. These plastic brackets have webbing to strengthen the corner and includes a set of alignment ribs designed to seat the bracket into the extrusion...

REV Robotics custom ATO sized auto-resetting breakers are designed to give reliable protection for FRC robot actuators.  These custom developed breakers adhere to SAE Standard J553 and will give consistent performance even after hundreds of breaker...

This bearing pillow block bracket (REV-41-1317) is used with the DUO Build System 15mm Extrusion. The 9mm center hole is use with either the Long Through-bore Bearing (REV-41-1329) or the End Cap Bearing (REV-41-1322) to provide a low friction shaft...

Steel hardware of the appropriate size to work with the ION Build System 1in Extrusion. Length measured from tip to underside of screw head. Specifications Material: 18-8 Stainless Steel Diameter & Thread: #10-32 Length: 3/8in Length:...

The REV M3 Nut Strip allows you to securely join plates and channels without the need for separate nuts. Simply thread bolts directly into the strip for fast and reliable assembly. Specifications Material: 6063 Aluminum Thread Pitch: M3 x 0...

Hex keys, also known as Allen wrenches or L-keys, are essential hand tools designed to drive screws and bolts with hexagonal recesses. They are widely used in robotics, engineering, and general assembly for tightening or loosening fasteners in compact or...

Designed specifically for the 2025 FIRST Global Challenge, this kit provides teams with the essential components needed to build a competitive and reliable robot. Packed with a carefully curated selection of mechanical, electrical, and control system...

The REV Smart Robot Servo V2 – available in Balanced and UltraSpeed configurations – is a fully configurable metal-geared servo designed to simplify servo-based mechanisms. Each SRS V2 can be used as a standard angular, custom angular, or...