FIRST Robotics Competition

These JST PH 6-pin Joiner Boards are intended to be used with the JST PH 6-pin Extension Cables to extend the reach of your NEO Brushless Motor sensor cables.

These SPARK PWM Cables have a JST-PH 4-pin connector on one end, and a 0.1in 3-pin female PWM connector on the other. They are designed to convert the SPARK MAX Motor Controller's PWM/CAN port to a standard 3-pin PWM port on a robot controller. The black...

These plastic clips are designed to keep standard 0.1" 3-pin PWM connectors together. Simply clip them around an assembled pair of connectors.

These plastic inserts are designed to go into the SPARK MAX Data Port to protect it from debris.

A custom-designed tool that allows teams to easily break and re-assemble #25 chain. The mandrel is used to push out the chain pin. If using connecting links, the pin can be completely removed, but the depth guide screw allows the option of partially...

The REV Robotics 2m Distance Sensor uses the ST Microelectronics VL53L0X Time-of-Flight (ToF) laser-ranging module to measure distances up to 2 meters with millimeter resolution. Unlike other ranging sensors that rely on the intensity of reflected light,...

The REV POE Injector Cable was specifically designed to address a common problem for many FRC teams with their wireless radios: intermittent power glitches. The wireless radios used in the last several FRC seasons can be powered either through a...

Blinkin makes adding LEDs to your robot as simple as driving a motor. Chose the pattern you want and give it the corresponding PWM signal. The REV Blinkin LED Driver is a compact LED driver module that simplifies controlling both 12V RGB LED and 5V...

Touch sensor is best used for user input, but can also be used as a limit switch.  Configuration The REV Touch Sensor is a digital sensor that is wired to the N+1 channel on our standard 4-pin JST PH connector. In other words, the REV Expansion Hub...

Nylon Zip Ties with rounded edges to prevent snagging. Length is idea for cable management and many other uses. Specifications 160mm long Quality nylon construction 18lb. tensile strength

 PWM Y-cable, is used for splitting the signal from the roboRIO so you can drive multiple motor controllers or servos from a single source. Specifications Length: 12in Wire colors: white, red, black Wire jacketing: black heat shrink tubing 22 AWG

2-pin header cable that can be used for connecting signals, sensors or any other spots on robots. Features 2 female 0.1in pitch connectors on each end.  Specifications Length: 91cm (36in) 2 pin receptacle on 0.1in pitch Wire Colors: red, black 22...

PWM Cables, which are used for connecting things like the SPARK Motor controller to the roboRIO. These can also be used as servo extension cables for getting signal and power a bit farther away than integrated wires can reach. Specifications Length:...

The Servo Power Module is a 6V 90W power injector that enables the use of high-power RC servos in applications where a robot controller cannot directly provide adequate power.  The Servo Power Unit passes through input signals unaltered while...

This #25 roller chain is designed for use with #25 sprockets. Each package includes 1 connecting link, and additional links are available separately in the #25 Connecting Links – 5 Pack. For custom chain lengths, we recommend the REV #25 Chain...

Connecting link for #25 chain. Use a connecting link to connect two ends of chain to create a loop. Specifications Material: Steel Size: #25 Pitch: 0.25in CAD & Drawings REV-41-1366 STEP File REV-41-1366 Onshape

The REV Smart Robot Servo (SRS) is a configurable metal-geared servo that takes the guesswork out of aligning and adjusting servo based mechanisms. One SRS can be used as a standard angular servo, a custom angular servo, and a continuous rotation servo...

The NEO 550 Brushless Motor is a member in the NEO family of brushless motors. Its output power and small size are specifically designed to make NEO 550 the perfect motor for intakes and other non-drivetrain robot mechanisms. Mounting holes and pilot...

The Through Bore Encoder V1 allows teams to place sensors in the locations closest to the rotation that they wish to measure. This rotary sensor measures both relative and absolute position through its ABI quadrature output and its absolute position...

The UltraPlanetary Female 5mm Output V2 is the output stage of the UltraPlanetary System. With two different ways to transfer power, the output stage allows designers to choose the option best suited for the application. The V2 version of the...

Split Lock washer with a 3/8in inner diameter. Specifications Material: Zinc-plated Steel ID: 3/8in OD: 0.680in Thickness: 0.094in Documentation ION Build System Guide #10 Hardware Basics CAD & Drawings REV-29-1240 Drawing

Steel hardware of the appropriate size to work with the ION Build System 1in Extrusion. Length measured from tip to underside of screw head. Specifications Material: 18-8 Stainless Steel Diameter & Thread: #10-32 Length: 1-1/2in Documentation ION...

The REV 4-Pin JST to PWM Sensor Adapter Cable allows for seamless connection of REV Robotics Sensors like the Magnetic Limit Switch and Potentiometer to the FRC Control System. Please note that this cable will not work for I2C type sensors. REV...

This 5V WS2812B Addressable RGB LED Strip is compatible with the REV Blinkin LED Driver (REV-11-1105). Each LED contains an integrated driver IC and three LEDs; a red, green, and blue LED. Each individual LED can be controlled to create colorful patterns...

This 12V RGB LED Strip is compatible with the REV Blinkin LED Driver (REV-11-1105). Each LED on the strip is wired in parallel and actually contains three embedded LEDs; a red, green, and blue LED. Each color can be controlled separately to create any...

The Magnetic Limit Switch is a three-sided active-low digital hall effect switch with three internal hall effect elements located on the top and sides of the sensor. The three elements are connected in parallel so that any one of them will trigger the...

The REV Robotics SRS Programmer is the key to unlocking all the smart features of the (SRS) Smart Robot Servo (sold separately). Switching between continuous rotation, standard servo, and custom angular modes is easy as pressing a button...

This Eye-to-Eye Turnbuckle is ideal for tensioning string, cordage, or cabling in linear motion applications. The welded eyes provide significantly more strength than bent eyes. Specifications Material: Steel Thread: M5 Retracted Length: 106mm +- 1mm...

The 1in Extrusion Endcap Slide allows teams to create compact and robust multistage lifts when combined with the 1in Linear Motion Kit (REV-15-1189) and the 1in Extrusion (REV-21-1000). The slide tab is offset allowing stages to fully nest when collapsed...

High-strength and low-stretch cord that is ideal for actuating lifts and other linear mechanisms. Also known as Spectra or Dyneema, this cord type minimizes the need for adjustments and re-tensioning after first assembly due to its low-stretch properties...

For use with the ION Build System 1in Extrusion to create linear motion.   Kit Contents QTY 1 - REV-21-1032 - Dual Bearing Plate QTY 1 - REV-21-1029 - Eccentric Bushing QTY 1 - REV-21-1030 - Concentric Bushing QTY 2 -...

The UltraPlanetary 1/2in Hex Adapter is designed to face mount to the UltraPlanetary gearbox and provide a convenient 1/2in hex output shaft that is commonly used in the FIRST Robotics Competition. The recommended hardware for mounting the...

These are the same inserts that are included with the Through Bore Encoder.  Specifications Weight(s):  3/8in Hex: 23.5g (0.051lbs) 5mm Hex: 24.0g (0.052lbs) 1/4in Round: 24.0g (0.052lbs) Kit Contents QTY 1 - 3/8in Hex to 1/2in Hex...

Aluminum Servo Arm that is compatible with the REV Smart Robot Servo. Lightweight and strong, this arm is best utilized under high and low torque applications. Specifications Material: 6061 Aluminum CAD & Drawings SKU-STP REV-41-1820 Onshape...

Eccentric bushings are used to hold our V-Groove Bearings (REV-29-1014) for linear motion applications. The hole is drilled off-center of the bearing axis so by rotating the bushing on its mounting bolt, the clearance between the wheel and track can...

This dual bearing plate holds two V-Groove Bearings (REV-29-1014) to create an easy linear motion system for the ION Build System 1in Extrusion (REV-21-1000). Using a combination of Concentric (REV-21-1030) and Eccentric (REV-21-1029) bushings, the user...

Concentric bushings are used to hold our V-Groove Bearings (REV-29-1014) for linear motion applications. Used in conjunction with our Eccentric Bushing (REV-21-1029), the user can adjust how tight or loose they would like to tune their linear...

The REV Robotics Analog Pressure Sensor is a 5V sensor that can measure pressures up to 200 PSI. It outputs an analog voltage that is proportional to the measured pressure and can plug directly into the roboRIO or the More Board V2.0. Applications ...

The UltraPlanetary 550 Motor Plate works with the REV HD Hex Motor, REV NEO 550 Brushless Motor, and other 550 class motors. The UltraPlanetary System offers a variety of mounting options, with four different brackets available for attachment to REV...

Complete gear set replacement for the Smart Robot Servo (REV-41-1097) Notes Replacement Gear Sets purchased after 03/27/2019 ship with updated versions of the replacement gears that fit the updated version of the Smart...

Extend the reach of your MXP port by using this 18" cable to reposition your boards where you need them. Fully compatible with all REV Robotics MXP accessory boards (More Board, Proto Board, & RIOduino) Specifications Keyed male and female...

The REV Robotics Digit is multi-use MXP board for interface with the roboRIO. It has four 12 segment displays, which can be used to show any letters or numbers. It also features an analog potentiometer and two momentary buttons. Teams can use the...

The robust 1in Inside Corner Bracket is designed to enable more construction strategies with the REV 1in Extrusion (REV-21-1000). Designed for #10 hardware, the mounting holes are on a 1in pitch that allows for the creation of complex joints by...

Steel hardware of the appropriate size to work with the ION Build System 1in Extrusion. Length includes the flat screw head. Specifications Material: 18-8 Stainless Steel Diameter & Thread: #10-32 Length: 1/2in Documentation ION Build System Guide...

These Low Profile Nylon Lock Nuts are thin enough to fit inside the channel of the ION Build System 1in Extrusion. The embedded nylon ring provides tight vibration resistant hold on the threads of the screw. Specifications Material: Zinc-plated Steel...

This cable is for use with the Blinkin LED Driver. This cable converts the JST PH 7-pin connector on the Blinkin' LED Driver module to a males 3-pin JST SM and male 4-pin JST SM connectors for connecting 5V WS2812 addressable LED and 12V RGB LED strips...