Shop All

The Through Bore Encoder V2 provides precise, reliable shaft position measurement with both incremental (ABI quadrature) and absolute (pulse-width) outputs. Its ½in hex through bore mounts easily within common FRC/FTC mechanisms, and the included...

Metal sprockets designed to work in high-load applications with #25 chain. This sprocket requires a hub like REV-41-1719. Specifications Chain Size: #25 Material: 6061 Aluminum Documentation SprocketGuide BuildingGuide Product...

REV Building System also comes in a 15mm x 30mm square extrusion. The slots are designed to fit standard M3 hardware rather than expensive t-nuts. Use the 15mm x 30mm extrusion when more strength is needed for an application. For smaller applications the...

REV 45mm U Channel has a 45mm x 45mm square profile, and is designed to work seamlessly with existing REV 15mm Extrusion. It can be used in locations where additional torsion strength is required. On the sides of the channel is the Extended Motion...

REV 45mm x 15mm C Channel has a 45mm x 15mm rectangular profile, and is designed to work seamlessly with existing REV 15mm Extrusion. It can be used in locations where additional torsional strength is required. The 45mm wide side of the channel...

The UltraUSB Hub is designed specifically for use in competitive robotics, and gives you the ability to connect multiple USB devices to each other as well as replacing cables when damaged instead of needing to replace the whole hub. The UltraUSB Hub can...

These JST PH 6-pin Extension Cables are intended to extend the reach of sensor cables without having to cut and splice wires. Specifications REV-11-1275-PK4: Length: 90cm (35.5in) REV-11-3327: Length: 30cm (11.81in)

REV 45mm Flat Plate is a 45mm wide, bendable metal featuring the Extended Motion Pattern. This product is a piece that is 440mm long. The Extended Motion Pattern supports M3 hardware for attaching brackets, extrusion, and channel...

This 90 degree inside corner bracket (REV-41-1320-PK8) is used with the DUO Build System 15mm Extrusion. These plastic brackets have webbing to strengthen the corner and includes a set of alignment ribs designed to seat the bracket into the extrusion...

REV Robotics custom ATO sized auto-resetting breakers are designed to give reliable protection for FRC robot actuators.  These custom developed breakers adhere to SAE Standard J553 and will give consistent performance even after hundreds of breaker...

This bearing pillow block bracket (REV-41-1317) is used with the DUO Build System 15mm Extrusion. The 9mm center hole is use with either the Long Through-bore Bearing (REV-41-1329) or the End Cap Bearing (REV-41-1322) to provide a low friction shaft...

Steel hardware of the appropriate size to work with the ION Build System 1in Extrusion. Length measured from tip to underside of screw head. Specifications Material: 18-8 Stainless Steel Diameter & Thread: #10-32 Length: 3/8in Length:...

Designed specifically for the 2025 FIRST Global Challenge, this kit provides teams with the essential components needed to build a competitive and reliable robot. Packed with a carefully curated selection of mechanical, electrical, and control system...

The REV Smart Robot Servo V2 – available in Balanced and UltraSpeed configurations – is a fully configurable metal-geared servo designed to simplify servo-based mechanisms. Each SRS V2 can be used as a standard angular, custom angular, or...

This is the version of the USB-A to USB-C cable that is included with the SPARK MAX Motor Controller and the Control Hub. Use this cable to connect your SPARK MAX or Control Hub to a standard computer from up to 1/2 meter away. Features This USB-C cable...

Upgrade your 3in MAXSwerve Module with this high-performance motor and controller package, featuring the latest NEO Vortex Brushless Motor and SPARK Flex Motor Controllers. Created for maximum efficiency and advanced control, this bundle is perfect for...

Commonly included with our gearboxes and pinion options, the 8mm Keyed Shaft Retaining Hardware Pack is compatible with the REV ION System and includes the hardware needed to retain 2mm keyed elements to 8mm OD shafts without the bulk of alternative...

The MAXLift #25 Chain Attachment Plate is a durable yet lightweight aluminum bracket designed for seamless use with the REV ION system within the MAXLift family of products. It simplifies mounting and assembly for elevator and lift systems. Featuring...

The 3in MAXSwerve Module – 15T Spline Input Kit is designed to adapt the REV NEO 2.0 Brushless Motor or Kraken X60 for use with the 3in MAXSwerve Module. This kit provides the necessary gearing and hardware to integrate a 15T spline drive motor...

The MAXPlanetary Kraken X44 & Minion Input Kit is a comprehensive solution for adapting Kraken X44 or Minion motors to the MAXPlanetary system. This kit includes the [REV-21-4444] MAXPlanetary Kraken X44 & Minion Adapter Plate, designed with...

The MAXLift Bearing Blocks are integral components of the MAXLift system, providing teams with a robust and space-efficient solution for building high-performance elevator assemblies. With the main blocks being designed around billet aluminum...

GT2 3mm Pitch Belts are compatible with both the REV ION System and the REV DUO System. These belts go hand in hand with GT2 timing pulleys. Use belts and pulleys in tight to fit areas where adjustment is difficult. Specifications Pitch: 3mm Width: 9mm...

Bearings 15T Spline Bearing - Flanged - 1.125in OD - 4 Pack (REV-21-3294-PK4) Featuring a 8mm internal diameter and a 1.125in outer diameter, this bearing is designed to fit into a MAXSpline bore while supporting a 15T Spline shaft. The flange adds a way...

#10-32 Shaft End Screw V1 and V2 are compatible with the REV ION System and are used to retain parts on any ION hex shaft instead of shaft collars. 1/2in Rounded Hex Shafts in various lengths are available and come tapped with #10-32 holes. The...

The 3in MAXSwerve Spiky Wheel - Hub and Tread Bundle includes everything needed to outfit your MAXSwerve-equipped robot with Spiky wheels for enhanced performance. The bundle contains four (4) balanced aluminum hubs, eight (8) Spiky split treads, and...

These ION Motor Brackets are compatible with the REV ION System. The ION UltraPlanetary Face Mount Bracket (REV-21-2046) allows for easy mounting of our UltraPlanetary Gearbox to any of our MAXTube products. Each plate features 2x #10-32 tapped inserts...

Designed for teams requiring higher load capacity in chain-driven systems, the ION #35 Sprockets come in three versatile options, each compatible with the REV ION Build System: #35 Hub Sprockets - 1/2in Hex: Featuring a 1/2in hex bore (rounded for the...

The 3in MAXSwerve Spiky Wheel Aluminum Hub is a durable replacement or backup hub designed specifically for the MAXSwerve system. Pair it with a fresh 3in MAXSwerve Spiky Wheel - Tread (REV-21-3094-PK8) and #10-32 3/8in button head screws for a high...

The 3in MAXSwerve Spiky Wheel Tread is designed for superior grip and performance in competitive robotics. Made from injection-molded thermoplastic polyurethane (TPU) with a Shore A durometer of 95, this tread offers an improved coefficient of friction...

The Aluminum Angle 0.74in x 0.74in is a robust and lightweight solution for attaching and connecting components in your robot design. Made from the same clear anodized aluminum as MAXTube, this angle iron-shaped extrusion is designed for compatibility...

The MAXPlanetary Double Motor Adapter seamlessly integrates with the REV ION Build System, enabling the side-by-side mounting of MAXPlanetaries, UltraPlanetaries, or SPARK Flex/NEO Vortex combos onto MAXTube - 2x1 with MAX Pattern. This compact solution...

#35 Connecting Links are compatible with the REV ION System and are design for use with #35 Roller Chain. Use a #35 Connecting Link to connect two ends of chain to create a loop. Specifications Material: Steel Size: #35 Pitch: 0.375in ...

#35 Roller Chain is compatible with the REV ION System. This product is a single strand of #35 Roller Chain for use with ION #35 Sprockets. Use a #35 Connecting Link to connect two ends of chain to create a loop. Specifications Material: Steel...

The #35 Chain Turnbuckle is compatible with the REV ION System. It is designed to adjust the length of a #35 Roller Chain by replacing a few links in a run and also allows the user to tension the chain by adjusting the turnbuckle. The...

The Ballast Block - 3in x 2in x 1in is a steel weight block weighing 1.42 pounds (643g), designed for easy integration with the ION Build System. It features a staggered hole pattern with twenty (20) #10-32 counterbored through holes and twenty (20)...

The Vortex Shaft - 15T Spline, compatible with the REV ION System and gives users the ability to drive inputs that have a 8mm diameter involute 15T spline. Compatible with SplineXS shaft components. Featuring a 1/2in hex section that drives the shaft and...